My Godlie lost its ATR

***fergs*** · 15-08-08, 01:43 PM

Hey all.

My goldie was workin fine & got home from work & its stopped..

I can still read it with GGe & all I can see is that its missing the ATR

how do I send / put it back on ??

My other backup is still working , but until it gets an ATR again..

it wont work..

what happened ?? old age !!!

**dizzy** · 15-08-08, 02:15 PM

just reprogram it

***fergs*** · 15-08-08, 02:19 PM

Quote:

Originally Posted by dizzy

just reprogram it

Tried to re do it with GGe but didnt work cause its got no ATR..

Any suggestions ??

**LeroyPatrol** · 15-08-08, 02:23 PM

try reprogramming the pic.

Leroy

***fergs*** · 15-08-08, 02:44 PM

Quote:

Originally Posted by LeroyPatrol

try reprogramming the pic.

Leroy

Unfortunately I dont have something like Elvis / Jaycar

I have a Mastera II & sometimes it just has a mind of its own (female) & today must be 1 of them days where it doesnt wanna do what I need it to...

Trying to get it to work with CardWriter atm..

**mickc** · 15-08-08, 02:47 PM

icprog works with mastera

***fergs*** · 15-08-08, 02:57 PM

Quote:

Originally Posted by mickc

icprog works with mastera

I have tried some old directions that i found ages ago..

But never had any success with icprog.

it will read the cards, but doesnt seem to do much more than that.

I obviously dont have either the complete directions OR I keep missing a "VITAL" step.

** EDITED**
win98se & com port1
ic-prog 1.05E & Mastera II set @ 3.5mhz (mode 1)

start it up & select PIC 16F84 & read all
then select Smart card Wizard & that all goes sweet

then my problems start...

this is where all the tuts for elvis / jaycar say to swap buttons / switch to ??? & Mastera doesnt have a switch. (change from PIC programmer to smart card programmer)

SO all I do is select the GFG v226 eeprom.hex & continue.

then error messages start

programming not supported or Reseting card failled etc.

**osci** · 15-08-08, 05:31 PM

I guess you would have tried re-programming the card at the 6Mhz setting?

***fergs*** · 15-08-08, 05:58 PM

Can some verify that I'm doing the correct steps ???

thanks

**adams** · 15-08-08, 10:57 PM

Quote:

Originally Posted by *fergs*

SO all I do is select the GFG v226 eeprom.hex & continue.

then error messages start

programming not supported or Reseting card failled etc.

I get to the same point with same error. I have just built the jaycar and was thinking I had stuffed up. So I will check some settings and report.

**adams** · 15-08-08, 11:23 PM

Success
Try this, in icprog go settings/option/smartcard and change from 6 to 3.58 mhz
All I need now is a friendly logger to send my HSN and provider ID

**adams** · 15-08-08, 11:25 PM

What is ATR

**adams** · 16-08-08, 04:28 PM

I tried the wizard set at 6Mhz and the Jaycar jumper set to 6 Mhz and it ran ok too.
The tutorial said to use jumper set to 3.58.
When I try the card in the STB I get Unknown card. Shouldn’t it be Service scrambled?
Either the it hasn’t encoded correctly or my D-10 MediaStar is incompatible. Any clues?

15-08-08, 01:43 PM	#1 (permalink)
*fergs* Senior Member iTrader: (0) Join Date: Jan 2008 Location: Perth Posts: 221 Spent time on board: 1 Week, 5 Days and 10:54:29	My Godlie lost its ATR Hey all. My goldie was workin fine & got home from work & its stopped.. I can still read it with GGe & all I can see is that its missing the ATR how do I send / put it back on ?? My other backup is still working , but until it gets an ATR again.. it wont work.. what happened ?? old age !!!

15-08-08, 05:31 PM	#8 (permalink)
osci Premium Member iTrader: (2) Join Date: Jan 2008 Posts: 550 Spent time on board: 1 Week, 1 Day and 3:09:57	I guess you would have tried re-programming the card at the 6Mhz setting? __________________ Democracy & Ignorance = A Winning Combination

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

15-08-08, 02:15 PM	#2 (permalink)
dizzy Premium Member iTrader: (0) Join Date: Jan 2008 Posts: 32 Spent time on board: 1 Day and 9:04:26	just reprogram it

15-08-08, 02:23 PM	#4 (permalink)
LeroyPatrol Premium Member iTrader: (14) Join Date: Jan 2008 Posts: 2,516 Spent time on board: 1 Month, 3 Weeks, 0 Days and 12:35:06	try reprogramming the pic. Leroy

15-08-08, 02:47 PM	#6 (permalink)
mickc Premium Member iTrader: (1) Join Date: Jan 2008 Posts: 393 Spent time on board: 1 Month, 1 Week, 6 Days and 10:12:39	icprog works with mastera

15-08-08, 05:58 PM	#9 (permalink)
*fergs* Senior Member iTrader: (0) Join Date: Jan 2008 Location: Perth Posts: 221 Spent time on board: 1 Week, 5 Days and 10:54:29	Can some verify that I'm doing the correct steps ??? thanks

15-08-08, 11:23 PM	#11 (permalink)
adams Member iTrader: (0) Join Date: Jan 2008 Posts: 66 Spent time on board: 4 Days and 22:05:02	Success Try this, in icprog go settings/option/smartcard and change from 6 to 3.58 mhz All I need now is a friendly logger to send my HSN and provider ID

15-08-08, 11:25 PM	#12 (permalink)
adams Member iTrader: (0) Join Date: Jan 2008 Posts: 66 Spent time on board: 4 Days and 22:05:02	What is ATR

16-08-08, 04:28 PM	#13 (permalink)
adams Member iTrader: (0) Join Date: Jan 2008 Posts: 66 Spent time on board: 4 Days and 22:05:02	I tried the wizard set at 6Mhz and the Jaycar jumper set to 6 Mhz and it ran ok too. The tutorial said to use jumper set to 3.58. When I try the card in the STB I get Unknown card. Shouldn’t it be Service scrambled? Either the it hasn’t encoded correctly or my D-10 MediaStar is incompatible. Any clues?

Sponsored Links

Sponsored Links

Sponsored Links

Sponsored Links