I've downloaded iGo (not Primo) along with the Aus Map and DEM data that Bazzle has uploaded recently with the emulator. It works a treat but dosn't have the base map. Is this an issue at all? I did notice when I run this on the PC that the default location is Sydney and there is water visible for the habour but as soon as you get the the ocean there is nothing. Same at other coastal area.
To try and rectify this I downloaded the base map using the folloiwng link:
. There are two base maps and I've downloaded each of these (the one from johnch121 and scanner1). After downloaed, one at a time I have copied this into the igo8\Content\Maps directory and started it up. The problem is it freezes iGo during the startup process. Bottom of the screen reads GEODB INITDBFILES. I'm assuming that the problem is the licencing of this map is not available (I believe each map including the Base map) has it's own licence. Any ideas how to resolve this or if my assumption about the licence is incorrect then put me in my place
OS Software Change? Hi Bazzle,Originally Posted by bazzle01
Maybe you can help? Just over a year ago I bought a Kogan G3 EziNav GPS the original unit came with iGO software installed but the unit went faulty and the replacement GPS came back with SYGIC software. Can I install the iGo software on the unit and if so how do I do this, your advice would be much appreciated.
Thanks Kopie
Have a look through post, it may help.
Disclaimer
Any resemblance to real persons, living or dead is purely coincidental. Use only as directed. Apply only to affected area.
If condition persists, consult your physician. Subject to change without notice. Please remain seated until the ride has
come to a complete stop. Contains a substantial amount of non-tobacco ingredients. For office use only. Do not write below
this line. STIMPY WAS HERE. Reproduction strictly prohibited. No solicitors. No anchovies unless otherwise specified.
Schaffer
Base map not require.
One you run it with an aerial it will find position and will save that point for next load.
Bazzle
Link is dead again
Might be this one?
Bazzle
mikeausa (21-12-10),tonyphil55 (18-12-10)
Thanks VERY MUCH
Link works now
Just a quick knobby question
will this work on these units ???
i just wanted to update my maps on it
When you do things right, people won't be sure that you have done anything at all
What Navi system is loaded on that? Pic looks like Tom Tom not iGO8.Just a quick knobby question
will this work on these units ???
i just wanted to update my maps on it
Bazzle
Hi bazzle01
Yeah " IGO My Way " shows up when i run the Navigation software
When you do things right, people won't be sure that you have done anything at all
Yep
This link no longer worksOz ones.
Put just the speedcam.spdb and speedcam.spud files from the zip in your speedcam folder in content. Empty folder 1st. (save your old ones in case you muck it up)
Bazzle
This works.
.
Is this one Sensis or Navteq ?
Cant remember
Download and have a squiz
Bazzle
I use both - have an SD chip with Navteq for Country driving (more side road I.D.), and one with Sensis for City (more signposting)
Or if you use the right skin just use map changer, that way you don't need to swap sd cards or even close down the program.
x2
I use with GJ6.18. Also works with Dimka.
Bazzle
Bazzle, I noticed on another forum that you said you have MapChanger running well after a few gliches.
I've tried following a couple of "How to's" but just can't get it operating, such as what do we Aussies call the Sensis Map folder?.
In my sys.txt my SD is called "%SDCARD%"
Can you either PM me with how you did yours (What goes where, I'm also using GJ6.18p_da) or a "How To" here?
This is my first "Please Sir" in a long while!!
Thanks - BlindPete
Last edited by BlindPete; 24-12-10 at 03:06 PM. Reason: added words
Blind Pete
Try here.
Bazzle
Posting Permissions
LinkBack URL
About LinkBacks
Reply With Quote
Bookmarks