price of cat5e install

**soft** · 04-06-08, 09:36 PM

What is the going rate of a network point wired and terminated these days for say a 25 to 30 meter run?

**Chimp** · 04-06-08, 09:55 PM

just 1 point???

**soft** · 04-06-08, 11:26 PM

need 28 points

**ben699** · 05-06-08, 12:56 AM

Private or done commerically?

Parts supplied? so just labour?

Where based as differant places charge differant rates.

Need cabinet?

**soft** · 05-06-08, 06:56 AM

Commercial Coburg Sockets Cable Supplied

**biggeorge** · 06-06-08, 02:34 PM

Cable supplied or already been run???

There's a lot of variables. Explain where it's at when when you want the dude to come in and hook stuff up, and what you want at the end.

**porkop** · 07-06-08, 08:14 AM

and whether or not you have to crawl under floors/roof's. Double story, internal walls, brick....the list goes on and on

**REG** · 07-06-08, 11:49 PM

Cat5e $120-$150 per point cat6 $180-$220 PP Panduit certified 25 years warrnt

**intelliGEORGE** · 09-06-08, 06:22 PM

What REG said is about the going rate. Obviously discounted in larger jobs.

**ben699** · 10-06-08, 12:31 AM

if you have parts supplied,
what is the building config?

you be about 100 an hour , probly take 2 to 3 days , just in labour.
I guess 14 doubles but

those 28 , are they 28 outlets or 28 doubles???

**manicretep** · 21-09-08, 08:07 AM

Also if the cable has been run by a non licensed Cabler, it would be unethical for a licensed cabler to connect sockets (as he could be fined), all cabling has to be compliant with ACMA regs,

If someone runs the cable I always charge the same as if I did it, I run a 15m single o/l the other day $ 165.00 inc gst, was a prick of a place, 2 dif roofs(to get between the front pc and the rear) 1.5hrs and duct

$ 125.00 to $ 220 is average here add $ 22 to make it a double.
or $ 66 p/h if you supply min 2 hrs.

28 outlets $ 3080.00 inc gst, cable, outlets and plates
$ 2772.00 if you supply cable and bits.
(site audit required to confirm price)

**mal** · 21-09-08, 09:50 AM

Did one a while ago with similar specs 34 points most were triple points I charged $135 per point after we had finish I did a costing and it would have worked out very close done on a hourly rate.
Do suggest you make sure they do a certification with a printed report of each point

04-06-08, 09:36 PM	#1 (permalink)
soft Junior Member iTrader: (0) Join Date: Feb 2008 Posts: 13 Spent time on board: 4:29:10	price of cat5e install What is the going rate of a network point wired and terminated these days for say a 25 to 30 meter run?

LinkBacks (?) LinkBack to this Thread: http://www.austech.info/networking-wireless-cabled/6973-price-cat5e-install.html
Posted By	For	Type	Date
Austech - Powered by vBulletin	This thread	Refback	25-09-08 09:43 PM
Ritmo NAS LAN 650 - 3.5" HDD enclosure with LAN / host USB on Networking - Wireless and Cabled \| BoardReader	This thread	Refback	23-09-08 08:25 PM
Networking - Wireless and Cabled [Archive] - Austech	This thread	Refback	13-09-08 01:10 PM
Austech - Powered by vBulletin	This thread	Refback	07-06-08 11:59 PM

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-06-08, 09:55 PM	#2 (permalink)
Chimp Senior Member iTrader: (1) Join Date: Jan 2008 Posts: 257 Spent time on board: 1 Week, 0 Days and 8:03:48	just 1 point???

04-06-08, 11:26 PM	#3 (permalink)
soft Junior Member iTrader: (0) Join Date: Feb 2008 Posts: 13 Spent time on board: 4:29:10	need 28 points

05-06-08, 12:56 AM	#4 (permalink)
ben699 Junior Member iTrader: (0) Join Date: Jan 2008 Posts: 20 Spent time on board: 2:17:59	Private or done commerically? Parts supplied? so just labour? Where based as differant places charge differant rates. Need cabinet?

05-06-08, 06:56 AM	#5 (permalink)
soft Junior Member iTrader: (0) Join Date: Feb 2008 Posts: 13 Spent time on board: 4:29:10	Commercial Coburg Sockets Cable Supplied

06-06-08, 02:34 PM	#6 (permalink)
biggeorge Huge Member iTrader: (0) Join Date: Jan 2008 Location: Super Duper Secret Members Forum Posts: 287 Spent time on board: 1 Day and 21:35:52	Cable supplied or already been run??? There's a lot of variables. Explain where it's at when when you want the dude to come in and hook stuff up, and what you want at the end.

07-06-08, 08:14 AM	#7 (permalink)
porkop Premium Member iTrader: (2) Join Date: Jan 2008 Posts: 452	and whether or not you have to crawl under floors/roof's. Double story, internal walls, brick....the list goes on and on

07-06-08, 11:49 PM	#8 (permalink)
REG Premium Member iTrader: (1) Join Date: Jan 2008 Posts: 57 Spent time on board: 4 Days and 4:57:33	Cat5e $120-$150 per point cat6 $180-$220 PP Panduit certified 25 years warrnt

09-06-08, 06:22 PM	#9 (permalink)
intelliGEORGE Premium Member iTrader: (2) Join Date: Jan 2008 Location: Antarctica Posts: 1,212 Spent time on board: 2 Weeks, 5 Days and 7:41:12	What REG said is about the going rate. Obviously discounted in larger jobs.

10-06-08, 12:31 AM	#10 (permalink)
ben699 Junior Member iTrader: (0) Join Date: Jan 2008 Posts: 20 Spent time on board: 2:17:59	if you have parts supplied, what is the building config? you be about 100 an hour , probly take 2 to 3 days , just in labour. I guess 14 doubles but those 28 , are they 28 outlets or 28 doubles???

21-09-08, 08:07 AM	#11 (permalink)
manicretep Registered User iTrader: (0) Join Date: Jul 2008 Location: Da boondocks Posts: 94	Also if the cable has been run by a non licensed Cabler, it would be unethical for a licensed cabler to connect sockets (as he could be fined), all cabling has to be compliant with ACMA regs, If someone runs the cable I always charge the same as if I did it, I run a 15m single o/l the other day $ 165.00 inc gst, was a prick of a place, 2 dif roofs(to get between the front pc and the rear) 1.5hrs and duct $ 125.00 to $ 220 is average here add $ 22 to make it a double. or $ 66 p/h if you supply min 2 hrs. 28 outlets $ 3080.00 inc gst, cable, outlets and plates $ 2772.00 if you supply cable and bits. (site audit required to confirm price)

Sponsored Links

Sponsored Links

Sponsored Links

Sponsored Links

21-09-08, 09:50 AM	#12 (permalink)
mal Premium Member iTrader: (3) Join Date: Jan 2008 Posts: 230 Spent time on board: 2 Weeks, 2 Days and 23:01:29	Did one a while ago with similar specs 34 points most were triple points I charged $135 per point after we had finish I did a costing and it would have worked out very close done on a hourly rate. Do suggest you make sure they do a certification with a printed report of each point