DM500s

**allover** · 02-10-08, 04:43 PM

2 DM500s, phoenix attached to 1 with nds card, ok on one box but when i go to CCcam thru the var/bin i cannot discipher the writing to get my f and c lines entered, tried window mode and all in list from drop down box in DCC
Have a cross over cable to go between boxes ?
Am using Toors phoenix and pli 2008 soft ware that was put up in April
Can any one put any light on this before i die of old age trying!!!!!
regards Allover

**oceanboy** · 02-10-08, 04:52 PM

Why are you using a phoenix for an NDS card?
And you can't share from the serial port.

So pop ya NDS card in the slot, set up ya configs and ip address's and you're done.

Anything else

Hint: This question has been asked many times on this forum, so a quick search will find you all the info and details you need

**Sanity** · 02-10-08, 05:06 PM

Quote:

Originally Posted by oceanboy

And you can't share from the serial port.

Yes you can

**oceanboy** · 02-10-08, 05:12 PM

Sorry... i think i was getting my whitey / internal slots and NDS all mixed up

**allover** · 02-10-08, 05:15 PM

Thanks ocean boy, but i have had so much trouble trying to do the direct connection with all the info and still could not get it to work, i am so frustrated i thought i would try the phoenix route
But i was able to enter cccam thru filezilla and open with Notepad++ and made the change, only thing that worries me is i see no card server? should i?
regards Allover

**oceanboy** · 02-10-08, 05:20 PM

Mmmmm you're not the brother of a couple of members here are you by chance?

You seem to be making it lot harder than it need be!?!
But i know that frustrated feeling

I use CuteFTP for my FTPing and config editing. It is very simple, give it a try.
How are you connecting to you boxes from the PC?
Why are you trying to connect them with a twisted pair, just use your router/modem and 4port switch or something. Then use normal patch leads.

Try starting with CuteFTP, sounds like that might be half your problem

To make one box the server and the other the client, there are lines you need to add to Ccam.cfg. So it knows what to do.
Those config lines have been posted here plenty of times. So take a look.

Trying taking it in steps.

1. Get your NDS card working in the internal slot
2. Set up both boxes on the network
3. Edit the Ccam.cfg file in each box (server with NDS card, client with C: line) or whatever cam you want to use.

If you do it in steps... at least you have less things to guess which might be wrong

Good Luck

**allover** · 02-10-08, 05:25 PM

Oceanboy, no pc, am trying to go from box to box for inter house use only.
Have printed the how toos but have never been able to fire it up and has now become an obsession and taking up too much of my time
No brothers 3 sisters
regards Allover

**oceanboy** · 02-10-08, 05:29 PM

Mmmmmm if you have no PC, how did you just post your last response?
Or use filezilla or notepad++???

Do you have internet on your phone? And a phone that runs those apps?

What are your Networking skills like?

You problem could be anywhere??
Wrong networking details, wrong networking hardware, wrong set ups in Ccam, etc etc.

How did you get your cams on the DM500s in the first place if you don't have a PC and your DM500s aren't on the lan with your router/modem?

Seems you might need to have a little think about all of this

**allover** · 02-10-08, 05:48 PM

No no no!!!
i know what you mean but the computer is one end of the house and box 1 other end and the other will be upstairs, should i just bite the bullet and install Newcs on the computer and run out of the router like every one else ? and save myself a lot of grief
Thanks for your replies

**oceanboy** · 02-10-08, 05:53 PM

Well, by the sounds, you are going to run a Cat5 cable anyway.... you may as well do the job properly don't you think

Or at least get a couple of wireless AP's for them.

Anyway.... it has been spelt out nice and simple here. Follow the steps and do a little reading and it will all happen with ease

As for joining 2 x DM500s with a standalone twisted pair crossover Cat5 cable, i have never done it. But have done many PC's that way in the old days when switchs and hubs cost a fortune. So i can't see why it wouldn't work

**allover** · 02-10-08, 05:56 PM

Thanks oceanboy

**porkop** · 02-10-08, 08:03 PM

Quote:

Originally Posted by allover

Thanks ocean boy, but i have had so much trouble trying to do the direct connection with all the info and still could not get it to work, i am so frustrated i thought i would try the phoenix route
But i was able to enter cccam thru filezilla and open with Notepad++ and made the change, only thing that worries me is i see no card server? should i?
regards Allover

its not that hard. one line the F: line on the server machine in CCcam.cfg and one line the C: line on the client machine.

Make sure each machine has a seperate IP address but in the same range.

stick your fox card in the server machine and up it comes!

**tuxmate** · 02-10-08, 10:16 PM

Just for you to check...........
There were posts about the MAC address being the same on clone DMs, which could be an issue if on the same network.

02-10-08, 04:43 PM	#1 (permalink)
allover Premium Member iTrader: (0) Join Date: Feb 2008 Posts: 97 Spent time on board: 5 Days and 11:48:12	DM500s 2 DM500s, phoenix attached to 1 with nds card, ok on one box but when i go to CCcam thru the var/bin i cannot discipher the writing to get my f and c lines entered, tried window mode and all in list from drop down box in DCC Have a cross over cable to go between boxes ? Am using Toors phoenix and pli 2008 soft ware that was put up in April Can any one put any light on this before i die of old age trying!!!!! regards Allover

02-10-08, 05:29 PM	#8 (permalink)
oceanboy Senior Member iTrader: (1) Join Date: Jan 2008 Posts: 1,166 Spent time on board: 2 Weeks, 5 Days and 7:15:34	Mmmmmm if you have no PC, how did you just post your last response? Or use filezilla or notepad++??? Do you have internet on your phone? And a phone that runs those apps? What are your Networking skills like? You problem could be anywhere?? Wrong networking details, wrong networking hardware, wrong set ups in Ccam, etc etc. How did you get your cams on the DM500s in the first place if you don't have a PC and your DM500s aren't on the lan with your router/modem? Seems you might need to have a little think about all of this Last edited by oceanboy : 03-10-08 at 12:11 AM.

02-10-08, 05:53 PM	#10 (permalink)
oceanboy Senior Member iTrader: (1) Join Date: Jan 2008 Posts: 1,166 Spent time on board: 2 Weeks, 5 Days and 7:15:34	Well, by the sounds, you are going to run a Cat5 cable anyway.... you may as well do the job properly don't you think Or at least get a couple of wireless AP's for them. Anyway.... it has been spelt out nice and simple here. Follow the steps and do a little reading and it will all happen with ease As for joining 2 x DM500s with a standalone twisted pair crossover Cat5 cable, i have never done it. But have done many PC's that way in the old days when switchs and hubs cost a fortune. So i can't see why it wouldn't work Last edited by oceanboy : 02-10-08 at 08:35 PM.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-10-08, 04:52 PM	#2 (permalink)
oceanboy Senior Member iTrader: (1) Join Date: Jan 2008 Posts: 1,166 Spent time on board: 2 Weeks, 5 Days and 7:15:34	Why are you using a phoenix for an NDS card? And you can't share from the serial port. So pop ya NDS card in the slot, set up ya configs and ip address's and you're done. Anything else Hint: This question has been asked many times on this forum, so a quick search will find you all the info and details you need

02-10-08, 05:12 PM	#4 (permalink)
oceanboy Senior Member iTrader: (1) Join Date: Jan 2008 Posts: 1,166 Spent time on board: 2 Weeks, 5 Days and 7:15:34	Sorry... i think i was getting my whitey / internal slots and NDS all mixed up

02-10-08, 05:15 PM	#5 (permalink)
allover Premium Member iTrader: (0) Join Date: Feb 2008 Posts: 97 Spent time on board: 5 Days and 11:48:12	Thanks ocean boy, but i have had so much trouble trying to do the direct connection with all the info and still could not get it to work, i am so frustrated i thought i would try the phoenix route But i was able to enter cccam thru filezilla and open with Notepad++ and made the change, only thing that worries me is i see no card server? should i? regards Allover

02-10-08, 05:20 PM	#6 (permalink)
oceanboy Senior Member iTrader: (1) Join Date: Jan 2008 Posts: 1,166 Spent time on board: 2 Weeks, 5 Days and 7:15:34	Mmmmm you're not the brother of a couple of members here are you by chance? You seem to be making it lot harder than it need be!?! But i know that frustrated feeling I use CuteFTP for my FTPing and config editing. It is very simple, give it a try. How are you connecting to you boxes from the PC? Why are you trying to connect them with a twisted pair, just use your router/modem and 4port switch or something. Then use normal patch leads. Try starting with CuteFTP, sounds like that might be half your problem To make one box the server and the other the client, there are lines you need to add to Ccam.cfg. So it knows what to do. Those config lines have been posted here plenty of times. So take a look. Trying taking it in steps. 1. Get your NDS card working in the internal slot 2. Set up both boxes on the network 3. Edit the Ccam.cfg file in each box (server with NDS card, client with C: line) or whatever cam you want to use. If you do it in steps... at least you have less things to guess which might be wrong Good Luck

02-10-08, 05:25 PM	#7 (permalink)
allover Premium Member iTrader: (0) Join Date: Feb 2008 Posts: 97 Spent time on board: 5 Days and 11:48:12	Oceanboy, no pc, am trying to go from box to box for inter house use only. Have printed the how toos but have never been able to fire it up and has now become an obsession and taking up too much of my time No brothers 3 sisters regards Allover

02-10-08, 05:48 PM	#9 (permalink)
allover Premium Member iTrader: (0) Join Date: Feb 2008 Posts: 97 Spent time on board: 5 Days and 11:48:12	No no no!!! i know what you mean but the computer is one end of the house and box 1 other end and the other will be upstairs, should i just bite the bullet and install Newcs on the computer and run out of the router like every one else ? and save myself a lot of grief Thanks for your replies

02-10-08, 05:56 PM	#11 (permalink)
allover Premium Member iTrader: (0) Join Date: Feb 2008 Posts: 97 Spent time on board: 5 Days and 11:48:12	Thanks oceanboy

02-10-08, 10:16 PM	#13 (permalink)
tuxmate Member iTrader: (0) Join Date: Mar 2008 Posts: 34 Spent time on board: 19:15:47	Just for you to check........... There were posts about the MAC address being the same on clone DMs, which could be an issue if on the same network.

Sponsored Links

Sponsored Links

Sponsored Links

Sponsored Links