Hi mate.What brand panel is it??
Check the two rails to Y and Z from smps.
Does it give a flash on screen at switchon??
Have a look for surface mount fuses on Y and Z.
Might be an indication of their failure.
Hi guys I am getting a Centrex Plasma model CTPL42S5
The customer says it has sound but no picture.
Just wondering if there is any common faults with these units or is it just going to be a Y sus board kit swap over again
cheers for your help
When you do things right, people won't be sure that you have done anything at all
Look Here -> |
Hi mate.What brand panel is it??
Check the two rails to Y and Z from smps.
Does it give a flash on screen at switchon??
Have a look for surface mount fuses on Y and Z.
Might be an indication of their failure.
Thanks mate I will throw it on the bench (as soon as I make some room LOL)
and get back to you
When you do things right, people won't be sure that you have done anything at all
Hi it's a Samsung panel there was no flash at switch on
there were a couple of lines down the bottom of screen
(pencil lines) there were a few sparkles a a minute later on screen
very very few sparkles about the size of my hand about 60 pixels LOL
checked all the fuses and fusible resistors and they seem fine just about to take some readings of the rails and then pull the Y board out and check to see if there are some surface mount fuses underneath the board
When you do things right, people won't be sure that you have done anything at all
Blah every thing tests fine
I'll have to pull the power supply out and see whats going on in there but all the rails seem to be there,I am all confused now LOL
When you do things right, people won't be sure that you have done anything at all
Centrex has gone out business, and do not know who else can support you ?
B4L Post the model on the panel.I have a 42 Samsung panel here thats pretty well new with Z Y and control boards.
Came out of a JVC from another service centre.
Hey Oscar it's a Samsung DPD Module model number S42SD-YD09
When you do things right, people won't be sure that you have done anything at all
Let ya know tomorrow Too dark outside now and beer is nice.
Ive got a 50 inch samsung that had a crook smps , so we ordered a new one , and its fixed but a month later the new smps went high rail and damaged other boards (exploded smd caps etc) a sad tale.
And its 800 bucks for the damaged digi board.
Got warranty on the supply .Bad luck about the rest.
Samsung
Bugger that, i get to scared when its big bucks.
You stay inside mate and I will gladly wait till tomorrow
cheers
When you do things right, people won't be sure that you have done anything at all
We got two but they appear to be earlier.
One is YD04 and the other is YD05
Both have their Y and Z boards intact.
Here is a pic
When you do things right, people won't be sure that you have done anything at all
that looks almost identical to my lg when i had to replace the three boards
Is that a Samsung sticker in the top/left corner?
Wish it was the same fandtm We,d have it fixed by now .
Can you give me some numbers off the Y and Z as I cant see em good enough in that picture to tell if what ive got are the same .
Sharpen up your photography lol.
I imagine what we have to be about 4 year old.
Its a brand new panel and I dont mind splitting it up as we will prolly never use it.
Y Main
Model: 42SD V5 Y-Main
PCB Code: LJ41-03431A
X Main
Model: 42SD V5 X-Main
PCB Code: LJ92-0343A
PCB Rev: R2.2 06/02/23
Cheers mate
When you do things right, people won't be sure that you have done anything at all
The V5 bit sounds promising .Ours is YD4 and 5.
Ive got a beer in front of me again lol
Will check in the morning.
Geez, that beer problem seems to be spreading, I'm looking at 6 or 7 relo's tvs i should be fixing, but oh no, beer. and another. oh god another. will it ever end?????
When I open my next repair shop I will call it "Alcoholics Anonymous"
When you do things right, people won't be sure that you have done anything at all
Bookmarks