Well I finally persisted with MioPocket and installed, my probelm was my directory on SD card had Destinator Apps instead of DestinatorApps. Ok MioPocket up and running and was able to runTTN7BOT.EXE and installed program ok.
Luck Duck
Looks like using MioPocket is too much fiddling for me. Just found out my son has new Tom Tom XL 4.3" and will lend me card :-) Then I have to figure how to point Flash memory to card Application.
Bugger, XL has no card.
Luck Duck
Last edited by Luck Duck; 09-07-09 at 03:40 PM.
Well I finally persisted with MioPocket and installed, my probelm was my directory on SD card had Destinator Apps instead of DestinatorApps. Ok MioPocket up and running and was able to runTTN7BOT.EXE and installed program ok.
Luck Duck
Last edited by Luck Duck; 10-07-09 at 12:27 PM.
Congratulations !
So it really pays off to be hard and tell you GPS : you are grounded for a week if I can't use you properly !!
Tomtom GO730 ,Navcore 9.004 ,Bootloader 5.5256 ,Map :Australia 845.2661ttmaps and Tomplayer on 16GB SDHC class6Password for all my files: downunder
That's not a problem with my files - it's your device, the native language of it is Dutch and Tomtom uses that !
Check post count #12...
Tomtom GO730 ,Navcore 9.004 ,Bootloader 5.5256 ,Map :Australia 845.2661ttmaps and Tomplayer on 16GB SDHC class6Password for all my files: downunder
Ah yes, I see my problem now and fixed it. I jumped the gun before I had fully finished the installation.
Also in step 9 I had to get the mapsetting.cfg file from Australia_830_2290 file as it wasn't in "TT7.WCE.4.2".
After finishing all the setup I deleted the folder "navigator".
However, now when Tom Tom starts a menu appears with Language selection on it and before I can select English I get an error message " Not enough memory available" Bugger, I thought my Destinator had enough memory for this program.
My Flash Memory looks like about 15MB and SD card is 1GB. Specs for my GPS is:
Smart Navi -400B - Hardware Specifications
CPU Samsung S3C2440 300Mhz
RAM 64MB SD RAM
ROM 32MB Flash ROM
Display 4.3 inch 260K Color TFT LCD
I/O BlueTooth, Mic, Stereo audio out, External GPS antenna jack Mini USB for mass storage
Expansion slot SD card
GPS SiRF III
OS WindowsCE.Net 4.2 Core
Application MP3, Movie player, Photo viewer
Luck Duck
Last edited by Luck Duck; 10-07-09 at 03:46 PM.
That is proplem for some devices ,I couldn't figure out what's causing it .
There is special version for the Tomtom EXE - I will try to find a link and post it here!
Tomtom GO730 ,Navcore 9.004 ,Bootloader 5.5256 ,Map :Australia 845.2661ttmaps and Tomplayer on 16GB SDHC class6Password for all my files: downunder
@LameDuck,
I had the same problem with the out of memory messages as you describe. However after starting from scratch several times on a newly formatted card it eventually installed properly and is now working fine. Suggest you persevere with it and it will come good.
Cheers, Ian
Any sufficiently advanced technology is indistinguishable from magic!
Do you have a planned route on your device?
You will need that!
Tomtom GO730 ,Navcore 9.004 ,Bootloader 5.5256 ,Map :Australia 845.2661ttmaps and Tomplayer on 16GB SDHC class6Password for all my files: downunder
Found something easier :
If that's not working try version - it might fix the memory problem ,but you will need to keep a planned route in your Tomtom.
I have not tried this release ,but it seems you have to replace the whole Tomtom installation - so before you try that make sure you got a planned route in your current Tomtom version ,maybe that's all you need.
The UPX version simply replaces the current file - so that is the easy way first
Last edited by Downunder35m; 10-07-09 at 06:58 PM. Reason: added a link
Tomtom GO730 ,Navcore 9.004 ,Bootloader 5.5256 ,Map :Australia 845.2661ttmaps and Tomplayer on 16GB SDHC class6Password for all my files: downunder
I do have a planned route for Canberra in Map directory Australia_830_2290 under Mapsettings.cfg address and in TT7.WCE.4.2 . I tried that TomTom UPX packed file and replaced existing TomTom navigator.exe (this file is smaller than original). TomTom loaded up and asked for language but English not among them :-( Anyhow it did start up without memory problem.
I switched the exe file back and got out of memory.
Luck Duck
Last edited by Luck Duck; 10-07-09 at 10:50 PM.
That's getting complicated here...
The language is not actually stored in the Navigator file as far as I know.
I'm running a bit out of ideas now.
The installation files are multilingual.
Can you start the "TTN7BOT.EXE" and configure Tomtom for English language and start the UPX file after that to see if it makes a difference?
Tomtom GO730 ,Navcore 9.004 ,Bootloader 5.5256 ,Map :Australia 845.2661ttmaps and Tomplayer on 16GB SDHC class6Password for all my files: downunder
Ok I reformatted my SD card and re did the install. point by point. I finally got Tom Tom up, selected English, voice and Australian map. Map came up on screen but after I exited I got "not enough memory available".
Selected navigate on my Destinator Menu and Tom Tom screen loads up again and on the screen flashes 4 maps with Select at bottom but before I could select the screen goes off and back to Destinator Menu.
Step 14 says always run TT7Navigator.exe to start, but that does not work ie nothing happens. But if I point to TomTom Navigator.exe it starts.
I'm nearly there. So I copied that file 7910CE42 over to SD card. Tom Tom starts then Menu appears saying Switching to Australia and another menu appears saying "Activation Failed. Sorry this is not the correct Activation Code for the product 'Australia' " Continue and of course same comes up again.
Ran key Gen again in case it needed to be done again but that didn't fix it.
Nothing about not enough memory this time so Memory is not an issue.
Luck Duck
Last edited by Luck Duck; 12-07-09 at 12:06 PM.
Try the to activate the map.
Tomtom GO730 ,Navcore 9.004 ,Bootloader 5.5256 ,Map :Australia 845.2661ttmaps and Tomplayer on 16GB SDHC class6Password for all my files: downunder
Did some checking on "not enough memory" on TomTom and some say maybe corrupt map file. So I unrarred the 0027.rar map file (which is the Australia_830_2290 map) to my SD card and got corrupt message:Tom Tom files\0027.rar: CRC failed in Australia_830_2290\cname.dat. The file is corrupt
So will download again and hope it is ok.
Luck Duck
The files inside the Rar-archive have to be unpacked to a folder in the root of your device(or SD card) anyway- it won't work with a Rar file for Tomtom
Tomtom GO730 ,Navcore 9.004 ,Bootloader 5.5256 ,Map :Australia 845.2661ttmaps and Tomplayer on 16GB SDHC class6Password for all my files: downunder
Persistence paid off, I ended up replacing the Navigator folder with one I backed up earlier that was installed ok. Then I got memory problem after start up and select map etc. I gave up and put gps on charger as battery very low. I came back 4 hours later to try again only this time I switched it on and up came select map and all the other configurations. Well well, I was able to put in my home address etc. looking forward to tomorrow when I will see how it goes with sat signal.
Thank you Downunder35m and others for the files and pointing me in the right direction, without that kind of support I might have given up.
Luck Duck
Bookmarks