Page 1 of 2 12 LastLast
Results 1 to 20 of 32

Thread: Concept 2000

  1. #1
    Junior Member SCT's Avatar
    Join Date
    May 2009
    Location
    Sydney Aust.
    Age
    62
    Posts
    190
    Thanks
    21
    Thanked 16 Times in 12 Posts
    Rep Power
    0
    Reputation
    72

    Default Concept 2000

    I have a Concept 2000 (old) that was collected after replacing it with a Tecom system.
    Does anybody know how to default the installer code on a 2000?
    I vaguely recall something about reversing the memory chip but I also recall being told that you'll fry the chip if you do.
    In the past I have had to return a panel to Security Merchants to have the installer code defaulted. Is this the only way?
    I think you can default a 1000 installer code by putting (temporarliy) a 2000 memory chip in place but not sure if there is a default procedure for the 2000 or not.
    Any suggestions??



Look Here ->
  • #2
    Senior Member
    intelliGEORGE's Avatar
    Join Date
    Jan 2008
    Location
    Sydney, AUSTRALIA
    Age
    43
    Posts
    4,106
    Thanks
    884
    Thanked 1,484 Times in 691 Posts
    Rep Power
    478
    Reputation
    7236

    Default

    If I remember correctly you need a 1000 board. You put the 2000 chip in the 1000 power up for 5-10 secs then power down. Put it back in the 2000 and enter the default code and that should work.

  • #3
    Member
    Join Date
    May 2008
    Posts
    254
    Thanks
    0
    Thanked 7 Times in 6 Posts
    Rep Power
    202
    Reputation
    49

    Default

    Thats correct and the same if you want to default a concept 1000 except you need a 2000 pcb.

    I've used the reverse chip thingy on several occasions but obviously there are risks. If you just want to use it as a test board though then the risks may be worth taking.

    I've never blown one up yet. If you do want to try it let me know and I'll pm you the best way of achieving this

  • #4
    Junior Member SCT's Avatar
    Join Date
    May 2009
    Location
    Sydney Aust.
    Age
    62
    Posts
    190
    Thanks
    21
    Thanked 16 Times in 12 Posts
    Rep Power
    0
    Reputation
    72

    Default

    Thanks guys...gotta love this forum!!!
    As soon as I saw the replies I went...Ahhhh thats right!!!
    Worked a treat. (lucky I still had a 1000 layin around as well)

  • #5
    Senior Member
    intelliGEORGE's Avatar
    Join Date
    Jan 2008
    Location
    Sydney, AUSTRALIA
    Age
    43
    Posts
    4,106
    Thanks
    884
    Thanked 1,484 Times in 691 Posts
    Rep Power
    478
    Reputation
    7236

    Default

    Quote Originally Posted by SCT View Post
    Thanks guys...gotta love this forum!!!
    As soon as I saw the replies I went...Ahhhh thats right!!!
    Worked a treat. (lucky I still had a 1000 layin around as well)
    Security merchants use to charge $40 for that!

  • #6
    Junior Member
    Join Date
    Jan 2008
    Posts
    186
    Thanks
    12
    Thanked 4 Times in 4 Posts
    Rep Power
    204
    Reputation
    27

    Default

    i thought the reverse chip method on the same model board defaulted the entire programming? does the 1000/2000 chip change just default the installer or entire programming?

  • #7
    Senior Member
    intelliGEORGE's Avatar
    Join Date
    Jan 2008
    Location
    Sydney, AUSTRALIA
    Age
    43
    Posts
    4,106
    Thanks
    884
    Thanked 1,484 Times in 691 Posts
    Rep Power
    478
    Reputation
    7236

    Default

    Quote Originally Posted by ya_mums_bum69 View Post
    i thought the reverse chip method on the same model board defaulted the entire programming? does the 1000/2000 chip change just default the installer or entire programming?
    Placing either 1000 or 2000 chips in their opposite boards, only defaults installer code.

  • #8
    Junior Member
    Join Date
    Jan 2008
    Posts
    186
    Thanks
    12
    Thanked 4 Times in 4 Posts
    Rep Power
    204
    Reputation
    27

    Default

    champion. learn something something new every day

  • #9
    Member
    Join Date
    May 2008
    Posts
    254
    Thanks
    0
    Thanked 7 Times in 6 Posts
    Rep Power
    202
    Reputation
    49

    Default

    Quote Originally Posted by intelliGEORGE View Post
    Placing either 1000 or 2000 chips in their opposite boards, only defaults installer code.

    Mmm, are you sure about that one? Could SCT confim this cos I thought it always did a full default.

  • #10
    Junior Member SCT's Avatar
    Join Date
    May 2009
    Location
    Sydney Aust.
    Age
    62
    Posts
    190
    Thanks
    21
    Thanked 16 Times in 12 Posts
    Rep Power
    0
    Reputation
    72

    Default

    Quote Originally Posted by Paulypudding View Post
    Mmm, are you sure about that one? Could SCT confim this cos I thought it always did a full default.
    Agreed. When I replaced the chip back into the 2000 the db was completely defaulted.

  • #11
    Junior Member SCT's Avatar
    Join Date
    May 2009
    Location
    Sydney Aust.
    Age
    62
    Posts
    190
    Thanks
    21
    Thanked 16 Times in 12 Posts
    Rep Power
    0
    Reputation
    72

    Default

    Quote Originally Posted by ya_mums_bum69 View Post
    i thought the reverse chip method on the same model board defaulted the entire programming? does the 1000/2000 chip change just default the installer or entire programming?
    Be careful! I had a notion that you could simply reverse the chip in the board (turn it around 180deg) to default installer code. I vaguely remember doing it on a 2000 in the past and got away with it but on other occasions it frys the chip (I think it's a bit hit and miss and not worth doing).
    As George says-swap the 1000 and 2000 chips to do a default.

  • #12
    Member
    Join Date
    May 2008
    Posts
    254
    Thanks
    0
    Thanked 7 Times in 6 Posts
    Rep Power
    202
    Reputation
    49

    Default

    Quote Originally Posted by SCT View Post
    Agreed. When I replaced the chip back into the 2000 the db was completely defaulted.
    Thats what I thought. I didn't think there was a way to just default the installer code. You can with the master code, but not the installer. (?)

  • #13
    Senior Member
    Arbiter's Avatar
    Join Date
    Oct 2008
    Posts
    1,408
    Thanks
    155
    Thanked 675 Times in 369 Posts
    Rep Power
    295
    Reputation
    3039

    Default

    Quote Originally Posted by intelliGEORGE View Post
    Placing either 1000 or 2000 chips in their opposite boards, only defaults installer code.
    Bullshit.
    Your $40 fee kept all existing programming and just set the Installer code back to 01.
    I must have done it a couple of thousand times.
    Reversing the chip does two things:
    1. It clobbers the directory structure in the Dallas NVRAM. No directory = no programming.
    2. It usually blows the bejeezuz out of the onboard lithium battery due to reverse polarity which means it is now a VRAM (Volatile).

    This does NOT work with a 1000 system. You lose all programming regardless.
    Last edited by Arbiter; 22-08-09 at 01:51 PM.

  • #14
    Senior Member
    Arbiter's Avatar
    Join Date
    Oct 2008
    Posts
    1,408
    Thanks
    155
    Thanked 675 Times in 369 Posts
    Rep Power
    295
    Reputation
    3039

    Default

    Quote Originally Posted by Paulypudding View Post
    Thats what I thought. I didn't think there was a way to just default the installer code. You can with the master code, but not the installer. (?)
    The Installer (User 000) cannot program Users on a 1000 or 2000 system.
    The Master User (User 001) can program all Users and reset the Installer back to factory default 01.

  • #15
    Member
    Join Date
    May 2008
    Posts
    254
    Thanks
    0
    Thanked 7 Times in 6 Posts
    Rep Power
    202
    Reputation
    49

    Default

    Quote Originally Posted by Arbiter View Post
    Bullshit.
    Your $40 fee kept all existing programming and just set the Installer code back to 01.
    I must have done it a couple of thousand times.
    Reversing the chip does two things:
    1. It clobbers the directory structure in the Dallas NVRAM. No directory = no programming.
    2. It usually blows the bejeezuz out of the onboatd lithium battery due to reverse polarity.
    That's fine but does putting the chips into the other version of board (ie, 2000 into a 1000 or vica versa) do a full default. Don't really know what inner range or whoever used to do to default. For reference I would like to know if the above defaults all or just installer.

  • #16
    Member
    Join Date
    May 2008
    Posts
    254
    Thanks
    0
    Thanked 7 Times in 6 Posts
    Rep Power
    202
    Reputation
    49

    Default

    Quote Originally Posted by Arbiter View Post
    The Installer (User 000) cannot program Users on a 1000 or 2000 system.
    The Master User (User 001) can program all Users and reset the Installer back to factory default 01.

    The master can do what? Never heard of that one. Think you may have got it around the wrong way. The installer is actually user 001 and the Master is user 000. The Installer can reset the Master back to 000.

  • #17
    Senior Member
    Arbiter's Avatar
    Join Date
    Oct 2008
    Posts
    1,408
    Thanks
    155
    Thanked 675 Times in 369 Posts
    Rep Power
    295
    Reputation
    3039

    Default

    Quote Originally Posted by Paulypudding View Post
    That's fine but does putting the chips into the other version of board (ie, 2000 into a 1000 or vica versa) do a full default. Don't really know what inner range or whoever used to do to default. For reference I would like to know if the above defaults all or just installer.
    Yes, this method does a full default ie all programming is lost.

  • #18
    Senior Member
    Arbiter's Avatar
    Join Date
    Oct 2008
    Posts
    1,408
    Thanks
    155
    Thanked 675 Times in 369 Posts
    Rep Power
    295
    Reputation
    3039

    Default

    Quote Originally Posted by Paulypudding View Post
    The master can do what? Never heard of that one. Think you may have got it around the wrong way. The installer is actually user 001 and the Master is user 000. The Installer can reset the Master back to 000.
    I agree and stand corrected.

  • #19
    Member redozqld's Avatar
    Join Date
    Aug 2008
    Location
    Here in Brisbane
    Age
    45
    Posts
    360
    Thanks
    7
    Thanked 24 Times in 18 Posts
    Rep Power
    205
    Reputation
    142

    Default

    Quote Originally Posted by SCT View Post
    I have a Concept 2000 (old) that was collected after replacing it with a Tecom system.
    Does anybody know how to default the installer code on a 2000?
    I vaguely recall something about reversing the memory chip but I also recall being told that you'll fry the chip if you do.
    In the past I have had to return a panel to Security Merchants to have the installer code defaulted. Is this the only way?
    I think you can default a 1000 installer code by putting (temporarliy) a 2000 memory chip in place but not sure if there is a default procedure for the 2000 or not.
    Any suggestions??

    There are several ways to do this :-

    1. Reverse the RAM Chip, power up with THE BATTERY ONLY, just for 1/2 of a second, now this can do one of many things
    1. Defaults All and your away!
    2. Doesnt Do Anything, and repeating the process isnt recommended
    3. Funny Blue Smokes comes out of the chip...
    2. Return the board to CSD, Wait 1/2 an hour for service, and then go back to the job, usually $80.00 poorer for the experience...
    3. Ask your friendly ReDoZ Technician... heheh ... I've got a lovely peice of tech that I got some time ago that allows you to default like SMA and CSD do and I do it for free.... if you send it to me...

    ReD

  • #20
    Senior Member
    intelliGEORGE's Avatar
    Join Date
    Jan 2008
    Location
    Sydney, AUSTRALIA
    Age
    43
    Posts
    4,106
    Thanks
    884
    Thanked 1,484 Times in 691 Posts
    Rep Power
    478
    Reputation
    7236

    Default

    Quote Originally Posted by Arbiter View Post
    Bullshit.
    Your $40 fee kept all existing programming and just set the Installer code back to 01.
    I must have done it a couple of thousand times.
    Reversing the chip does two things:
    1. It clobbers the directory structure in the Dallas NVRAM. No directory = no programming.
    2. It usually blows the bejeezuz out of the onboard lithium battery due to reverse polarity which means it is now a VRAM (Volatile).

    This does NOT work with a 1000 system. You lose all programming regardless.
    I agree reversing the chip does wipe it completely and could damage the chip, but as for putting a C2K chip in a C1K board, I have seen this done about a 100 times when taking in C2K chips to SMA, that's all they did. Power down the C1K put the 2K chip in power up then test 01, power down then remove the chip.

  • Page 1 of 2 12 LastLast

    Similar Threads

    1. Concept 4000 Wireless Lan?
      By Privatteer in forum Security Alarms
      Replies: 6
      Last Post: 21-10-10, 06:51 PM
    2. Concept and scripting
      By noRbackwards in forum Security Alarms
      Replies: 2
      Last Post: 18-07-09, 04:44 PM
    3. New ISP for families. (Concept)
      By z1gg33 in forum General Chat
      Replies: 14
      Last Post: 28-04-09, 07:06 AM
    4. Concept IQ
      By AusSecTec in forum Security Alarms
      Replies: 21
      Last Post: 28-01-08, 10:10 PM
    5. Concept 2000 panel
      By z80 in forum Security and Privacy
      Replies: 3
      Last Post: 06-01-08, 02:54 AM

    Bookmarks

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •