BF430 and GWM

**LeroyPatrol** · 16-06-08, 10:02 PM

Hi there,

I have a 5410z with a season connected to a BF430 which I gave an IP and port no. I have added a BFxxx client with the Host Name (IP addr) and port no. It appears in GWM as connected but in the 'CAM key/IP Addr' field it says Reset stb. I have tried powering on and off the box and reiserting the season. This had been working somewhere else.
Any ideas would be appreciated!!

Leroy

**Superior** · 16-06-08, 10:16 PM

If it is a card type season try pushing it further in to the card slot.
or in the case of a internal season re check your connections.
it sounds like its not making contact Correctly.

**LeroyPatrol** · 16-06-08, 10:25 PM

Quote:

Originally Posted by Superior

If it is a card type season try pushing it further in to the card slot.
or in the case of a internal season re check your connections.
it sounds like its not making contact Correctly.

It's a slot type. Thought I'd try this before mounting the internal. Card slot works as I tried with a goldie so the switch works also. The red lead comes on as there is a red and green led. Don't know what else to tell you.

Leroy

**fandtm666** · 16-06-08, 10:28 PM

if its an internal type i bet you dont have a dummy card in the card reader
this is a must.

if its a standard season put a bit of tape on the back so its a tight fit, it could be that its not keeping the reset pressed in.

**LeroyPatrol** · 16-06-08, 10:34 PM

Quote:

Originally Posted by fandtm666

if its an internal type i bet you dont have a dummy card in the card reader
this is a must.

if its a standard season put a bit of tape on the back so its a tight fit, it could be that its not keeping the reset pressed in.

Using a std season at the moment. Card pushed right in. If you pull it out a little the red led goes off.

Leroy

**fandtm666** · 16-06-08, 10:43 PM

log into the unit and make sure it is set to

username and pass = admin

1:realcom mode
2: make sure that the
ip
subnet = ( same as that your network card says )
gateway = ( same as that your network card says )
primary dns = ( same as that your network card says )
are all set correctly

**LeroyPatrol** · 16-06-08, 10:49 PM

Quote:

Originally Posted by fandtm666

log into the unit and make sure it is set to

username and pass = admin

1:realcom mode
2: make sure that the
ip
subnet = ( same as that your network card says )
gateway = ( same as that your network card says )
primary dns = ( same as that your network card says )
are all set correctly

all checked and set to rs232 9600baud. Here is the log from gwm

16 Jun 2008 22:49:13 HUMAX5410 No Data - Reset Connection
16 Jun 2008 22:49:14 HUMAX5410 Try Reconnect
16 Jun 2008 22:49:16 HUMAX5410 Host [10.1.1.155] IP [10.1.1.155]
16 Jun 2008 22:49:16 HUMAX5410 Send ATR
16 Jun 2008 22:49:16 HUMAX5410 [3B9F255E495244455445555143535555352E339E]
16 Jun 2008 22:49:17 HUMAX5410 Line State : [DCD Low - DTR Low - DSR High - RTS Low - CTS High]

Leroy

**conan_oz** · 16-06-08, 11:11 PM

Quote:

Originally Posted by LeroyPatrol

all checked and set to rs232 9600baud. Here is the log from gwm

Leroy

Like Fandtm666 the BF must be set to "real com" mode in the Operation Mode
and not TCP. If you dont have real com mode you will need to flash the unit with new firmware.

**LeroyPatrol** · 16-06-08, 11:14 PM

Quote:

Originally Posted by conan_oz

Like Fandtm666 the BF must be set to "real com" mode in the Operation Mode
and not TCP. If you dont have real com mode you will need to flash the unit with new firmware.

yep real com mode and firmware for the record is 1.06.02,Feb 10 2006

Leroy

**LeroyPatrol** · 16-06-08, 11:26 PM

I just noticed the latency in gwm says like more than 200000

Leroy

**conan_oz** · 16-06-08, 11:35 PM

Quote:

Originally Posted by LeroyPatrol

I just noticed the latency in gwm says like more than 200000

Leroy

GWM settings for bf

RapidShare: Easy Filehosting

**fandtm666** · 17-06-08, 07:18 AM

by the sound of it there is no communication from the humax , have a look at the units status to see what communication there is.

log in and then select status also make sure you have set the port forward in you router for the unit

**LeroyPatrol** · 17-06-08, 07:19 AM

Quote:

Originally Posted by conan_oz

GWM settings for bf

RapidShare: Easy Filehosting

Hi Conan,

How can I view this as html?

Leroy

**LeroyPatrol** · 17-06-08, 07:37 AM

Quote:

Originally Posted by fandtm666

by the sound of it there is no communication from the humax , have a look at the units status to see what communication there is.

log in and then select status also make sure you have set the port forward in you router for the unit

It comes up as 'connected' in GWM. The port is setup and the unit is on a local subnet.

**fandtm666** · 17-06-08, 07:46 AM

1: double check the the bf unit is not using the same port as gw

2: once gw is started just check that it has started the client , eg : right click and start i have found some times it actually does not and shows connected from a previous attempt which was recorded.

3: double check your serial cable.

4: double check the season

5; try the season connected via serial connection in gw and see if it fires up

6: humor me and forward the port even though its on a local lan, this has been an issue i have found in the past while doing various test with these units.

7: also double check that gw was setup correctly here is a quick guide i made up for it a while back it in powerpoint format

Idiot_s_guide_for_GWM

8: also with a few units i have tested the 5410z wont give pictures if it has not been d-zeded

**LeroyPatrol** · 17-06-08, 08:20 AM

Quote:

Originally Posted by fandtm666

1: double check the the bf unit is not using the same port as gw

2: once gw is started just check that it has started the client , eg : right click and start i have found some times it actually does not and shows connected from a previous attempt which was recorded.

3: double check your serial cable.

4: double check the season

5; try the season connected via serial connection in gw and see if it fires up

6: humor me and forward the port even though its on a local lan, this has been an issue i have found in the past while doing various test with these units.

7: also double check that gw was setup correctly here is a quick guide i made up for it a while back it in powerpoint format

Idiot_s_guide_for_GWM

8: also with a few units i have tested the 5410z wont give pictures if it has not been d-zeded

1/ When you say not using the same port, the BF is on 50000 and the client in GWM is 50000. This is not the same as others.

2/I had to right click start to initially get it started.

3/&4/checked season and cable

5/I would of tried connecting the season directly but I only have one comm port on my laptop. I left the driver disk at work for my USB/serial converter

6/ N/A as no router

7/ Don't tell me this that it may need to be dezederated!

GWM says status is connected and CAMKEY/IP Addr is Reset stb and when I remove season from slot it changes to not connected

I just restarted GWM and its status is Running but CAMKEY/IP Addr is not connected..

Hmmm.....Leroy

**jimbo123** · 17-06-08, 10:28 AM

I can't read either of those attachments, i.e. Conan's or 666's. I've renamed them , removing the x put on the end. I've assumed that Conan's is a word doc and 666's a powerpoint ? Anyone else had the same ?

Not good news with the Hummie maybe needing to be dezedded though

Jim.....

**seeu** · 17-06-08, 10:53 AM

Word 2007

**jimbo123** · 17-06-08, 10:57 AM

Quote:

Originally Posted by seeu

Word 2007

Guess we need to go looking for new things. Thanks for the reply.

**fandtm666** · 17-06-08, 12:36 PM

Quote:

Originally Posted by jimbo123

I can't read either of those attachments, i.e. Conan's or 666's. I've renamed them , removing the x put on the end. I've assumed that Conan's is a word doc and 666's a powerpoint ? Anyone else had the same ?

Not good news with the Hummie maybe needing to be dezedded though

Jim.....

yes mine was created with power point 2k7

16-06-08, 10:02 PM	#1 (permalink)
LeroyPatrol Premium Member iTrader: (14) Join Date: Jan 2008 Posts: 2,504 Spent time on board: 1 Month, 2 Weeks, 6 Days and 21:43:27	BF430 and GWM Hi there, I have a 5410z with a season connected to a BF430 which I gave an IP and port no. I have added a BFxxx client with the Host Name (IP addr) and port no. It appears in GWM as connected but in the 'CAM key/IP Addr' field it says Reset stb. I have tried powering on and off the box and reiserting the season. This had been working somewhere else. Any ideas would be appreciated!! Leroy

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

16-06-08, 10:16 PM	#2 (permalink)
Superior Premium Member iTrader: (0) Join Date: Mar 2008 Posts: 22 Spent time on board: 4 Days and 16:42:12	If it is a card type season try pushing it further in to the card slot. or in the case of a internal season re check your connections. it sounds like its not making contact Correctly.

16-06-08, 10:28 PM	#4 (permalink)
fandtm666 Premium Member iTrader: (19) Join Date: Jan 2008 Posts: 1,297	if its an internal type i bet you dont have a dummy card in the card reader this is a must. if its a standard season put a bit of tape on the back so its a tight fit, it could be that its not keeping the reset pressed in.

16-06-08, 10:43 PM	#6 (permalink)
fandtm666 Premium Member iTrader: (19) Join Date: Jan 2008 Posts: 1,297	log into the unit and make sure it is set to username and pass = admin 1:realcom mode 2: make sure that the ip subnet = ( same as that your network card says ) gateway = ( same as that your network card says ) primary dns = ( same as that your network card says ) are all set correctly

16-06-08, 11:26 PM	#10 (permalink)
LeroyPatrol Premium Member iTrader: (14) Join Date: Jan 2008 Posts: 2,504 Spent time on board: 1 Month, 2 Weeks, 6 Days and 21:43:27	I just noticed the latency in gwm says like more than 200000 Leroy

17-06-08, 07:18 AM	#12 (permalink)
fandtm666 Premium Member iTrader: (19) Join Date: Jan 2008 Posts: 1,297	by the sound of it there is no communication from the humax , have a look at the units status to see what communication there is. log in and then select status also make sure you have set the port forward in you router for the unit

17-06-08, 07:46 AM	#15 (permalink)
fandtm666 Premium Member iTrader: (19) Join Date: Jan 2008 Posts: 1,297	1: double check the the bf unit is not using the same port as gw 2: once gw is started just check that it has started the client , eg : right click and start i have found some times it actually does not and shows connected from a previous attempt which was recorded. 3: double check your serial cable. 4: double check the season 5; try the season connected via serial connection in gw and see if it fires up 6: humor me and forward the port even though its on a local lan, this has been an issue i have found in the past while doing various test with these units. 7: also double check that gw was setup correctly here is a quick guide i made up for it a while back it in powerpoint format Idiot_s_guide_for_GWM 8: also with a few units i have tested the 5410z wont give pictures if it has not been d-zeded

17-06-08, 10:28 AM	#17 (permalink)
jimbo123 Premium Member iTrader: (5) Join Date: Jan 2008 Location: Melbourne Posts: 346 Spent time on board: 3 Weeks, 6 Days and 18:10:33	I can't read either of those attachments, i.e. Conan's or 666's. I've renamed them , removing the x put on the end. I've assumed that Conan's is a word doc and 666's a powerpoint ? Anyone else had the same ? Not good news with the Hummie maybe needing to be dezedded though Jim.....

17-06-08, 10:53 AM	#18 (permalink)
seeu Premium Member iTrader: (2) Join Date: Jan 2008 Posts: 60 Spent time on board: 2 Days and 5:30:51	Word 2007

Sponsored Links

Sponsored Links

Sponsored Links

Sponsored Links