Search:

Type: Posts; User: Johnno

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    53
    Views
    1,197

    My 12v 200w panel (off ebay) has been charging a...

    My 12v 200w panel (off ebay) has been charging a 100ah battery for a few years now..(mppt charger located next to batt)
    It's wired to run 8 x 15w led lights under my verandah and shed light. That's...
  2. Replies
    20
    Views
    1,164

    I always tell people.. If you use the printer...

    I always tell people..

    If you use the printer for home use (couple prints a week) I would buy a cheap piece of shit printer and when the ink runs out, go and buy another Cheap piece of shit.
    ...
  3. Replies
    3
    Views
    958

    Normally Bad control boards.. El-cheapo Printers...

    Normally Bad control boards.. El-cheapo Printers only..
  4. Replies
    57
    Views
    2,626

    Hehe... The Trolley Man should use that money to...

    Hehe... The Trolley Man should use that money to pay off his fines.. lol winner
  5. Replies
    5
    Views
    809

    Yep, check the power cord.. you never know.. ...

    Yep, check the power cord.. you never know..

    With the Brother MFC-J680dw it'll be the Main Board PCB. I've seen the same thing many times.

    Throw away job.
  6. Replies
    5
    Views
    809

    Hi, can you give me the model number ? Most of...

    Hi, can you give me the model number ?

    Most of the low end inkjet machines 'No Power' means the main board is stuffed..

    If it's a laser printer most likely it's the PSU that's faulty. It'll be...
  7. That's awesome. Great pic.

    That's awesome. Great pic.
  8. Yes the Cheerful Spaniard Raul is very helpful....

    Yes the Cheerful Spaniard Raul is very helpful. Glad you got it running properly Well done. Saved yourself a few $$$$.
  9. Edit...

    Edit...
  10. https://s22.postimg.cc/giwh8bl2l/Yfi_ZDey.jpg...

    https://s22.postimg.cc/giwh8bl2l/Yfi_ZDey.jpg

    Un screw the side covers off and check the solenoid (found this pic on the net) careful incase there's plastic tabs instead of screws
  11. Thread: Home Phone

    by Johnno
    Replies
    20
    Views
    1,150

    I have a $17 pm deal with telstra for my land...

    I have a $17 pm deal with telstra for my land line.. mainly used for incoming calls as outgoing calls cost heaps.
    I use the mobile for outgoing calls.
  12. Yes, New printers are inexpensive.. especially...

    Yes, New printers are inexpensive.. especially for the small home office sector.. $50.00 will be just fine if you only want to print a few documents per day.
    The Companies, Corporations, Businesses,...
  13. If dust gets into the clutch it will cause paper...

    If dust gets into the clutch it will cause paper jams, if the solenoid looks faulty, check the spring on the plunger. They tend to loose tension.
    If you can't figure it out and your located in...
  14. If it's not picking up the paper from the tray,...

    If it's not picking up the paper from the tray, it could be a number of things.
    Check the cam gear on the paper tray itself. Sometimes it can be located on the body and lifts a lever on the tray....
  15. Replies
    3
    Views
    2,014

    Hi, I think it's the same one ......

    Hi, I think it's the same one ... (150-0264-01-01_Rev-A_Release) A Windows PC is connected to the RS232 port or RJ45.

    Pm me with an email if needed.

    Cheers
  16. Replies
    3
    Views
    2,014

    Hi, can only help with monitoring software and a...

    Hi, can only help with monitoring software and a user manual for the Xantrex 2.8 Inverter.. had problems with my display pcb and could never locate a schematic.
  17. Thoic then here...it was well before 2008.. i...

    Thoic then here...it was well before 2008.. i recall it being called cdcopyworld.
    congratulations all
  18. Replies
    16
    Views
    2,027

    My Relook 400 is working fine, it's setup just...

    My Relook 400 is working fine, it's setup just like a dreambox. There's very little difference.
  19. Replies
    24
    Views
    2,211

    have u tried running newcs in the Local Disk C: ...

    have u tried running newcs in the Local Disk C:

    eg:

    C:\newcs 1.65

    try not to run it in C:\my documents\etc\etc\newcs
  20. Replies
    1
    Views
    551

    Happy birthday mate, :) The Gamma team wishes...

    Happy birthday mate, :)

    The Gamma team wishes u all the best and so do all the cardsharing authors..Lol :D
  21. Replies
    39
    Views
    2,295

    Spot on Mango and Enf, am i that F#$kin old...lol...

    Spot on Mango and Enf, am i that F#$kin old...lol

    i was dragged here by Ku along with all the old timers when thoic died.

    arhh, the good old days, when moscing was all the rage..and wafers...
  22. Replies
    21
    Views
    2,071

    Well he ain't gunna fit in the back of my...

    Well he ain't gunna fit in the back of my supercharged Torrie...
    i had him sitting on the bonet, he loved the vibrations..lol :D
  23. Replies
    21
    Views
    2,071

    hehehe, :D :D Lol @ davo

    hehehe, :D :D Lol @ davo
  24. Replies
    21
    Views
    2,071

    KISS and HUGS 4 z80..lol onya Davo..:D was it...

    KISS and HUGS 4 z80..lol onya Davo..:D was it u that told me he likes tongue..;)
  25. Replies
    8
    Views
    4,299

    Hey Guys, Is the GW711 service manual the same as...

    Hey Guys, Is the GW711 service manual the same as the GW712 ? If Not, does anyone have one?
    My sister just rang me and asked if i could have a quik look at her GW712au.
    The Water Level light...
Results 1 to 25 of 87
Page 1 of 4 1 2 3 4