Search:

Type: Posts; User: moayad

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    261

    Tecom V8 Relay numbering.

    I have single door controller connected to V8 Panel.
    The RAS number is 2.
    My question is what is the address of the relay on the RAS2.
    I need to trigger the relay once the card is tapped on the...
  2. Replies
    2
    Views
    309

    Thank you mate for your reply I am adding the 4...

    Thank you mate for your reply
    I am adding the 4 door controller with Wiegand reader inputs to the V8 Tecom Panel.
    I could not add my HID Multiclass Card reader to the panel and was not able to the...
  3. Replies
    2
    Views
    309

    which card reader to use with Tecom V8?

    Hi.
    I have V8 Tecom, it works fine with users arming and disarming the areas using the Keypads.
    I am trying to add new door controller to the panel with card readers and doors (maglocks or door...
  4. Replies
    5
    Views
    585

    One of the technicians uses some marbles in a...

    One of the technicians uses some marbles in a small bag near the glass break to test the sensor and he said it works.
  5. Replies
    5
    Views
    585

    I tried shaking the keys near the glass break,...

    I tried shaking the keys near the glass break, the sensor start blinking only but was not enough to unseal the zone.
  6. Replies
    5
    Views
    585

    Glass break sensor testing.

    Hi.
    I need to test a glass break sensor.
    I used a keys and glass break tester by interlogix but it did not trigger the Interlogix Glasd break sensor.
    Any suggestion about the best glass break...
  7. Inner Range Concept 3000/4000 Factory Default.

    I bought an used Concept 3000/4000 panel.
    I tried to default the panel or the installer code by putting a jumper in LK3 and LK4 but did not work. I also tried putting a jumper in LK3 only as the...
  8. Replies
    5
    Views
    885

    I think you should get more than 0.8 volt coming...

    I think you should get more than 0.8 volt coming out from the panel.
  9. Replies
    1
    Views
    454

    1-remove the battery. 2-power down the panel....

    1-remove the battery.
    2-power down the panel.
    3-power up the panel.
    4- within 10 second type 97319731 in the keypad.
    5-the panel I defaulted.
    6-default installer code 9731
    7-default master code...
  10. Full site alarm test with Tecom Challenger Panel.

    Hi.

    I have a job end of this week of doing full alarm test of a site that has Pirs, Smoke detectors, Glass breaks, DGPs, and door reeds.
    The site has offices and a big warehouse.
    The Alarm...
  11. Full Site Alarm Test with Tecom Challenger Panel.

    Hi.

    I have a job end of this week of doing full alarm test of a site that has Pirs, Smoke detectors, Glass breaks, DGPs, and door reeds.
    The site has offices and a big warehouse.
    The Alarm panel...
  12. Replies
    5
    Views
    582

    I will try all those ways. I have v8 at home just...

    I will try all those ways. I have v8 at home just for training before going to any job.
  13. Replies
    5
    Views
    582

    and what should show the status of the PIR if...

    and what should show the status of the PIR if there is a cut in the cable ? I mean no resister in the circuit? it will still show unsealed or open?
  14. Replies
    5
    Views
    2,988

    it happened with me . I called Hikvision...

    it happened with me .
    I called Hikvision support and they access my laptop remotely an I had to export them a file of each camera and they sent my the reset file, I did no need to hard reset the...
  15. Replies
    2
    Views
    1,603

    I call Hikvision support and ask them to access...

    I call Hikvision support and ask them to access my laptop remotely to access the NVR or DVR and try to reset the password. they need the serial number of the device
  16. Thread: Mirror adhesive

    by moayad
    Replies
    8
    Views
    1,401

    I removed the mirror arm, and used two bolt and...

    I removed the mirror arm, and used two bolt and nut to hold it, I did not even used an adhesive and it is permanent.
  17. Replies
    5
    Views
    582

    Testing Inputs PIRs in Tecom Challenger 10

    Hi.
    This I my first post in the forum.
    I need to test few PIRs connected to Tecom Challenger DGP. and they are sending false alarm signals
    My problem is the PIRs are not labelled which means I...
Results 1 to 17 of 17