Page 2 of 2 FirstFirst 12
Results 21 to 36 of 36

Thread: FG XR6 Turbo '1 tonner'

  1. #21
    Premium Member
    hoe's Avatar
    Join Date
    Jan 2008
    Age
    60
    Posts
    6,367
    Thanks
    266
    Thanked 4,596 Times in 1,948 Posts
    Rep Power
    1820
    Reputation
    70528

    Default

    Just sent it to the Perth depot for a while....

    Might have to get the sprint out of the shed, it's still got 25km on it....

    Sent from my LON-L29 using Tapatalk



  • #22
    Junior Member
    Join Date
    Jun 2017
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Reputation
    10

    Default

    Awesome ute. I also have a xr6 turbo ute that i use for work. I have fitted all the one tonne suspension gear and load rated wheels. Just wondering on what your results were with the gvm upgrade letter to ford? All okay from ford?

  • #23
    Premium Member
    hoe's Avatar
    Join Date
    Jan 2008
    Age
    60
    Posts
    6,367
    Thanks
    266
    Thanked 4,596 Times in 1,948 Posts
    Rep Power
    1820
    Reputation
    70528

    Default

    Ford didn't want to know about it.
    Got gvm upgrade via local mechanic.

    Sent from my LON-L29 using Tapatalk

  • #24
    Junior Member
    Join Date
    Jun 2017
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Reputation
    10

    Default

    I figured the case. So most mechanics and suspension shops should be able to sort it out. Have been carrying 500kg+ constant and over the legal gvm, better sort it out.

  • #25
    LSemmens
    lsemmens's Avatar
    Join Date
    Dec 2011
    Location
    Rural South OZ
    Posts
    10,585
    Thanks
    11,867
    Thanked 7,061 Times in 3,338 Posts
    Rep Power
    3153
    Reputation
    132592

    Default

    How is the Ute going now, Hoe, must be just about ready to clock a million KM.
    I'm out of my mind, but feel free to leave a message...

  • #26
    Premium Member
    hoe's Avatar
    Join Date
    Jan 2008
    Age
    60
    Posts
    6,367
    Thanks
    266
    Thanked 4,596 Times in 1,948 Posts
    Rep Power
    1820
    Reputation
    70528

    Default

    Sent it to the perth depot a while ago, not doing anywhere near tbe distances now. The standard fgs are much cheaper to run, mainly because i cant find load rated 17 inch tyres that wear more than 30k. Cant fit 16 inch as they wont go over the turbo brakes.

    Got a couple more low km ex gov fg one tonners, but really hard to get now.

    Sent from my SM-T355Y using Tapatalk

  • #27
    Junior Member
    Join Date
    Jun 2017
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Reputation
    10

    Default

    Why not just fit the smaller disc brakes on the turbo? You can get 18 inch tyres with good load ratings cheap as well. I run a 245 45 18 with 102 load rating on my fg ute.

  • #28
    Premium Member
    hoe's Avatar
    Join Date
    Jan 2008
    Age
    60
    Posts
    6,367
    Thanks
    266
    Thanked 4,596 Times in 1,948 Posts
    Rep Power
    1820
    Reputation
    70528

    Default

    Quote Originally Posted by 78xcgxl View Post
    Why not just fit the smaller disc brakes on the turbo? You can get 18 inch tyres with good load ratings cheap as well. I run a 245 45 18 with 102 load rating on my fg ute.
    Load rating is not the problem, it's the softer compounds of the larger tyres.
    As I have employees driving it I can't modify the brakes.

    Sent from my LON-L29 using Tapatalk

  • #29
    Premium Member
    hoe's Avatar
    Join Date
    Jan 2008
    Age
    60
    Posts
    6,367
    Thanks
    266
    Thanked 4,596 Times in 1,948 Posts
    Rep Power
    1820
    Reputation
    70528

    Default

    Just an update, finally had to change the tailshaft as the centre bearing was noisy @440000km.
    Took it to a specialist reconditioner and cv joints are fine, just needs a new centre bearing.....
    He agrees with me that the problem with the turbo utes spitting out tailshafts is the weak rear springs allowing the tailshaft to rotate which causes the cv joint to lock up as the angle becomes too great.

    He's never seen a turbo with that amount of km on it, let alone with the original tailshaft.....

    Sent from my CLT-L29 using Tapatalk

  • The Following User Says Thank You to hoe For This Useful Post:

    hinekadon (12-04-19)

  • #30
    Senior Member
    Godzilla's Avatar
    Join Date
    Jul 2008
    Location
    Melbourne
    Age
    59
    Posts
    12,740
    Thanks
    16,580
    Thanked 7,201 Times in 3,648 Posts
    Rep Power
    2198
    Reputation
    79113

    Default

    I was just a day ago at melbourne drive shafts getting a tailshaft made up for a build in working on.

    While there i thought id ask about my FG Turbo ute getting a new rear CV fitted to the original shaft.

    Last one was fitted at 95,000, utes now at 270,000, so 4 factory shafts in 95,000 and then right through till now on that last one (mind you its still OK just i can feel it a little)

    He slides under and mentions at the last tailshaft warranty claim i did that they fitted a FGX Turbo shaft in.

    He mentioned they added a extra CV joint just after the center bearing on the FGX utes to take care of the failures however that my biggest savior was that i fitted lowered King springs but with the reverse eyelets which brings the pinion angle down and has 5 leafs to stop the springs from winding up.

  • #31
    Junior Member
    Join Date
    Jan 2011
    Posts
    121
    Thanks
    121
    Thanked 32 Times in 21 Posts
    Rep Power
    173
    Reputation
    420

    Default

    the weak rear springs allowing the tailshaft to rotate .
    How many kms have you driven this ute?

  • #32
    Premium Member
    hoe's Avatar
    Join Date
    Jan 2008
    Age
    60
    Posts
    6,367
    Thanks
    266
    Thanked 4,596 Times in 1,948 Posts
    Rep Power
    1820
    Reputation
    70528

    Default

    Diff housing to rotate excessively due to weak springs......

    Sent from my VOG-L09 using Tapatalk

  • The Following User Says Thank You to hoe For This Useful Post:

    kclar (20-04-19)

  • #33
    Premium Member
    hoe's Avatar
    Join Date
    Jan 2008
    Age
    60
    Posts
    6,367
    Thanks
    266
    Thanked 4,596 Times in 1,948 Posts
    Rep Power
    1820
    Reputation
    70528

    Default

    Yes, I just dropped my tailshaft at the rebuilder and he said mine was one if the rare ones with the extra cv joint and big centre bearing.

    It's an fg 2012.

    He reckons they are no problem in 1000hp builds.
    BTW, a stock non turbo one fits fine, just use the non turbo flange bolts.


    Sent from my VOG-L09 using Tapatalk

  • #34
    Senior Member
    Godzilla's Avatar
    Join Date
    Jul 2008
    Location
    Melbourne
    Age
    59
    Posts
    12,740
    Thanks
    16,580
    Thanked 7,201 Times in 3,648 Posts
    Rep Power
    2198
    Reputation
    79113

    Default

    Nope, even the FGX tailshafts are twisting like alloy Coke cans at well under 1000Hp (Its the torque, not the Hp and hooking up that destroys them)

    Seen some really scary twisted FG tailshafts in a pile at a well know Ford big power builder recently, he tells me the walls are still the same thickness and they just get new ones made up at G J Drivelines in Keysbourgh.

    Looking at some of the twisted failures, the tailshafts were pretty rusted in the tubes from inside, outside they were nice and painted black, typical Ford saving every penny they can.

    A little tip i was given that i didnt know about by the guy doing my tailshaft, spacers are now being fitted to bring the rear of the tranny down a little, its been making quite a difference to some big powered builds by fixing issues with the angles on the tailshaft joints.

  • The Following User Says Thank You to Godzilla For This Useful Post:

    lsemmens (03-06-21)

  • #35
    Junior Member
    Join Date
    Jun 2020
    Location
    Griffith NSW
    Posts
    1
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Reputation
    10

    Default

    Sorry to dig up an old thread for my first post but not many people seem to turn turbos into tonners.

    What are the specs/model of the wheels & particularly the tyres? I'm struggling to find a wheel/ tyre combo to fit my turbo work ute front end with the load ratings for the back end.

    & what did you end up getting the Gvm upgraded too? I weighed my Turbo tank with the tool canopy I just set up for it and came in at 2.88T.

    Thanks for any help guys

  • #36
    Premium Member
    hoe's Avatar
    Join Date
    Jan 2008
    Age
    60
    Posts
    6,367
    Thanks
    266
    Thanked 4,596 Times in 1,948 Posts
    Rep Power
    1820
    Reputation
    70528

    Default

    bit of an update. the turbo ute has nearly half a million kays on it.
    still on the same tailshaft, no real dramas, just a diff centre replaced to reduce the whine......

    its getting a bit tired, still pulls well and uses bugger all oil between services, but its idling a bit rough and the turbo seals are letting a bit of oil through.

    now to find a good barra turbo workshop in perth for a rebuild to sprint specs......

    any recommendations ?

  • Page 2 of 2 FirstFirst 12

    Bookmarks

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •