Results 1 to 6 of 6

Thread: Accidentally burned a tiny R265 component while removing a CAP

  1. #1
    Junior Member
    Join Date
    Dec 2015
    Posts
    10
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Reputation
    10

    Default Accidentally burned a tiny R265 component while removing a CAP

    Hi Guys,

    I was trying to repair an old tv, while removing a Capacitor, I have accidentally burned a tiny component. Please see the image below. Can you please advise what this is called? Can it be replaced?






    thanks,
    Sam
    Last edited by samdiy; 17-04-17 at 07:35 AM.



Look Here ->
  • #2
    Senior Member
    Reschs's Avatar
    Join Date
    Aug 2010
    Location
    Outside a few schooners
    Posts
    3,080
    Thanks
    908
    Thanked 2,147 Times in 1,058 Posts
    Rep Power
    933
    Reputation
    33238

    Default

    R205 is the circuit ID. So a resister. Can you read the number on it ?

    Do you have the circuit ?

  • #3
    Junior Member
    Join Date
    Jan 2015
    Posts
    40
    Thanks
    1
    Thanked 8 Times in 7 Posts
    Rep Power
    117
    Reputation
    170

    Default

    The little numbers on the black component itself will tell you the value. There is a chance they are all the same looking at how they are arranged, so if you look at the numbers on the one next to the one that burned, they might be the same. Once you know the value, the part is less than a dollar but you might have to buy 10 of them.

  • #4
    Senior Member
    Uncle Fester's Avatar
    Join Date
    Jan 2008
    Location
    Commonly found in a pantry or the bottom of a fridge, searching for grains, fermented or distilled
    Posts
    6,405
    Thanks
    2,289
    Thanked 4,414 Times in 2,517 Posts
    Rep Power
    2046
    Reputation
    81778

    Default

    You didn't burn it, you removed it and it is very likely still stuck on the tip of your soldering iron if you didn't continue to use it much.
    It could be competely covered in solder.
    This does not damage or burn the resistor. They are designed to handle that.

    Heat up the iron and flow some fresh fluxed solder over the tip and it may reveal itself. Prod around the tip with a thin screwdriver or something that does not attract solder and you can slide it off.
    Otherwise slide the tip along some desoldering wick.
    These smd resistors can appear a lot smaller when the are not on the circuit board, so wear some magnifiying reading glasses or something, so you don't miss it.
    Last edited by Uncle Fester; 17-04-17 at 12:51 PM.
    Update: A deletion of features that work well and ain't broke but are deemed outdated in order to add things that are up to date and broken.
    Compatibility: A word soon to be deleted from our dictionaries as it is outdated.
    Humans: Entities that are not only outdated but broken... AI-self-learning-update-error...terminate...terminate...

  • #5
    Junior Member
    Join Date
    Jun 2013
    Location
    Maryborough, Qld
    Posts
    32
    Thanks
    12
    Thanked 9 Times in 7 Posts
    Rep Power
    136
    Reputation
    170

    Default

    Quote Originally Posted by samdiy View Post
    I was trying to repair an old tv...
    I'm an old fart but with magnifying glasses, good light and a pair of good tweezers I can manage to resolder these little ants okay enough to work again.
    So, I think we are looking at a bunch of resistors in series which will reduce voltage. The picture isn't clear but it appears the two each side of the one you removed are the same. You would know better than us on that score. Good bet the missing one is the same as those. Measure across the two each side and get the resistance or match the numbers - same thing. If you have some 1/4W resistors laying around you could solder one of them in or as advised, you have to buy a bunch of them to use just the one ;-(
    Good luck!
    philbo

  • #6
    Member tw2005's Avatar
    Join Date
    Oct 2010
    Location
    Mancave
    Posts
    308
    Thanks
    51
    Thanked 114 Times in 84 Posts
    Rep Power
    208
    Reputation
    1743

    Default

    well , what do we know? Not that you've given many clues.

    It's plasma, It's Panasonic, It's most likely a 2009 early 2010, it's 12th Generation, size and series unknown could be S,G, or V, 10 /15 , 42 -50"

    90% of the board number is showing.

    In that resistor series, R264,R265,R266,R267

    R264 ERJ6ENF4422 M44.2KOHM, 1/10W
    R265 ERJ6ENF4422 M44.2KOHM, 1/10W
    R266 ERJ6ENF4422 M44.2KOHM, 1/10W
    R267 ERJ6ENF4422 M44.2KOHM, 1/10W

    Interesting thing here is when you look up that part number, Panasonic quotes 1/8W as the spec, so run with 1/8W at least

    also be interesting to hear what blink code the TV was throwing if it's faulted



    Last edited by tw2005; 20-04-17 at 08:23 PM.

  • Bookmarks

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •