-
Junior Member
- Rep Power
- 199
- Reputation
- 90
XP home with BAD_SYSTEM_CONFIG_INFO error
Hi austech-heads
Hopefully SOMEONE can help me with this one ...
I have a Dell Inspiron 8600 which only had 512M RAM. I acquired two 1G sticks of supposedly compatible RAM and did the swap. The system worked fine for a few startups but has thrown a number of blue screens of death, the latest being:
A problem has been detected and windows has been shut down to prevent damage to your computer.
BAD_SYSTEM_CONFIG_INFO
If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps:
Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need.
If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable any components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode.
Technical Information:
*** STOP: 0x00000074 (0x00000003, 0x00000002, 0x80088000, 0xc000014c)
... which I cannot resolve.
I have swapped the old memory back into the system, but cannot get past this error. I cannot boot from the Windows CD to do a windows repair. (I get to the screen to choose Repair, but when I select to repair c:\Windows I simply get dropped into the DOS prompt). When I try to boot into Safe Mode, it Blue Screen's during the loading of drivers but I can't see which it fails at (or which is the last that is successfully loaded).
HELP!!!
flashfletch
Last edited by flashfletch; 09-09-08 at 10:48 PM.
Reason: more info ...
-
Double check you have put your original ram in correctly and in the correct slot, well try both slots, that stop message normally is to do with ram.
If you can get into the bios select default settings and save.
A google of the error message shows a couple strange occurrences that caused that error.... registry files set to read only or all the files in C:\WINDOWS\system32\config set to read only. You need to have a boot disk with ntfs capabilities to get into the drive to change this though, or know how to use the recovery console.
With regards to the repair if you select repair using recovery console it does drop you to a dos like prompt where you need to enter commands see
You can do a repair install by skipping this first repair, past the licensing agreement and then do a repair install, you keep all your data etc, but need to install all updates again, see
Junior Member
- Rep Power
- 199
- Reputation
- 90
Thaks ssrattus
I'm currently doing a Dell diagnostic run on the windows blue screen tests. It's got to the HDD tests without a fail in memory so ... (I don't know)
When the testing is finished, I will try to repair options you have suggested.
Thanks. Here's hoping....
flashfletch
Junior Member
- Rep Power
- 199
- Reputation
- 90
Sadder and sadder!!
Diagnostics are showing up an error on the Read test for the HDD (Error Code 0F00:0244, Block 54318943 - Uncorrectable data error or media is write protected)
Looks like this thread should be in the Hardware forum instead ...? Must be a windows driver located at that block and that's why I'm Blue Screening (?).
Still waiting for the diagnostics to finish. I will keep the info updated.
flashfletch
Junior Member
- Rep Power
- 199
- Reputation
- 90
Also an error on the same block during the Verify test (not surprising).
?Time for a new HDD???
What brand and size of hard drive is it?
I'd try the repair install in the link I gave, if it works get the data off and then test the hd again.
To hook a laptop drive to the desktop you need a laptop hd to ide adapter, ebay and many computer stores have them for a few dollars or you could get a laptop hd to usb adaptor and use it that way.
Junior Member
- Rep Power
- 199
- Reputation
- 90
Thanks everyone for advice/help. Turns out it is almost certainly a dodgy HDD. Had a Dell tech around for another machine (this one's out of warranty) and while he was waiting he talked me through the testing required and it got narrowed down to one dead block in the Windows area of the HD. Couldn't get any repair functions to work, so I guess that I'm just going to have to replace and rebuild. Fortunately I was able to get all the data off the HD.
Keep up the great work helping us tyros.
flashfletch
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Bookmarks