Results 1 to 3 of 3

Thread: Solar system to charge 24v and 12v batteries

  1. #1
    Junior Member
    Join Date
    Jul 2008
    Location
    Riverton N.Z.
    Age
    66
    Posts
    59
    Thanks
    9
    Thanked 1 Time in 1 Post
    Rep Power
    126
    Reputation
    20

    Default Solar system to charge 24v and 12v batteries

    In my campervan I have 2 solar array arrangements.

    Both charge my 12v house batteries.
    One system is a 24v array, 500w MPPT controller.
    Second system is 12v array, 250 watt MPPT controller.

    Is it possible to connect an additional PWM controller directly to the 2v array and the 24v start batteries to keep them on float charge.

    I have tried a succession of buck/boost chargers on the 12v array, but they have not been up to the job.

    With thanks.

    Robin
    Ultraplus 680 platinum. 1.1 triax on moteck with 3 lnbs, 1.8 prime focus Dual C/ku lnb. 75 dish with 3 lnbs in campervan.



Look Here ->
  • #2
    Senior Member
    nomeat's Avatar
    Join Date
    Jan 2008
    Location
    Commonly found in a pantry or the bottom of a fridge, searching for grains, fermented or distilled
    Posts
    4,089
    Thanks
    1,099
    Thanked 1,924 Times in 1,180 Posts
    Rep Power
    905
    Reputation
    31978

    Default

    You would need to boost the 12V system to 27.6V (or whatever the float voltage of your batteries are specified), no need for another battery controller if this is just for floating. You just need to see that the step up voltage convertor (boost circuit) is up the to required amperage when the battery is low.

    This step up converter should be up to the job for the 12V 250W system:


    You set the output voltage to 27.6V before you connect it to the battery and then limit the current with the current adjuster to match the power of your panels. To do this you then connect the batteries which should not be fully charged(still in the bulk phase) and measure the voltage of the panels while you adjust the current limiter and when it is around 17-18V on the panels you got the right setting. Never mind if the output voltage on the battery is lower at that moment, it wll eventually reach the required floating voltage when the battery is charged. I would also disconnect the other 24V system from the battery when you do this setting.

    This is done normally of course when it is reasonably sunny but for some reserve I would not do the adjustment in the midday sun. Maybe at 10:00 or 14:00.

    You should have an additional proper solar charger to fully charge and equalise the batteries occasionally, which I assume comes from the 24V system.
    Last edited by nomeat; 18-05-18 at 12:08 AM.
    $$$...Welcome to Australia where corruption is legalized...$$$

    The only group that does not have a lobby is the middle income taxpayer.

  • The Following 2 Users Say Thank You to nomeat For This Useful Post:

    rawill (24-05-18),tristen (18-05-18)

  • #3
    Junior Member
    Join Date
    Jul 2008
    Location
    Riverton N.Z.
    Age
    66
    Posts
    59
    Thanks
    9
    Thanked 1 Time in 1 Post
    Rep Power
    126
    Reputation
    20

    Default

    Thank you for the link.
    That is a much more robust unit than I have at the moment.
    I am going to save the details for it.

    However the unit I am trying now is working. Fitted to the 12v array and stepped up to 27.4 float.
    All seems good.
    Ultraplus 680 platinum. 1.1 triax on moteck with 3 lnbs, 1.8 prime focus Dual C/ku lnb. 75 dish with 3 lnbs in campervan.

  • Bookmarks

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •