Results 1 to 5 of 5

Thread: Bosch solution 3000 won’t let me add a second keyfob to the panel

  1. #1
    Junior Member
    Join Date
    Jun 2018
    Location
    QLD
    Posts
    2
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Reputation
    10

    Unhappy Bosch solution 3000 won’t let me add a second keyfob to the panel

    Having some issues with a keyfob not registering with the Bosch Sol 3000 panel. Have gotten one registered under location 301 which operates alarm away/stay/panic/garage door. The second remote that came with the WE800EV2 kit won’t register with the panel no matter what I try. Tried different keyfob locations (I.e. 302, 309, 321) and it always gives an error beep.

    This is what I’ve been doing: mastercode+1 away > 302 away > away again > (keypad zones flash) press button 1 or 2 on remote > (keypad displays last digit of keyfob code) away then it does the long error beep. Normally I would press away twice and it would register no problems.

    Have tried deleting all keyfobs and reprogaming them in and have the same issue, one works other doesn’t. The garage operates fine using button 3 even though it’s not able to arm the system (just to point out that the remote works)).

    Lost



Look Here ->
  • #2
    Junior Member
    Join Date
    Jul 2009
    Location
    Brisbane
    Posts
    67
    Thanks
    4
    Thanked 9 Times in 9 Posts
    Rep Power
    112
    Reputation
    80

    Default

    is this a existing or new install? your process for registering the keyfobs looks right.
    existing install: you could look at the user authority locations and make sure its programmed right ie: arm/disarm ect
    new install: default the panel & program the fobs back in with out too much other time spent on other programming locations ie: zones ect
    the keyfob could be faulty? does the receiver blink when you press the arm and/or disarm button not sure if the WE800 receiver even has a light

  • #3
    Junior Member
    Join Date
    Jun 2018
    Location
    QLD
    Posts
    2
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Reputation
    10

    Default

    Hi 2Secure,

    fresh new install. The WE800 receiver does have a light when the button is pressed henced button 3 is working. Might check authority level but that hasn’t been meddled with apart from changing one user to master. Might have to default and try again - pretty easy to do.

    Any other suggestions?

  • #4
    Junior Member
    Join Date
    Jul 2009
    Location
    Brisbane
    Posts
    67
    Thanks
    4
    Thanked 9 Times in 9 Posts
    Rep Power
    112
    Reputation
    80

    Default

    does the WE800 light go when any of the other buttons are pressed ? if it doesn't light up then i would think the keyfob is faulty
    what button did you use to learn this keyfob in with ? did you have to press multiple buttons until it registered

    looking at your original post i seem to think the keyfob is a dud

    you did mention that button 3 works, is this for both keyfobs?

  • #5
    Junior Member
    Join Date
    Jun 2016
    Posts
    35
    Thanks
    0
    Thanked 4 Times in 4 Posts
    Rep Power
    27
    Reputation
    90

    Default

    Quote Originally Posted by Cowiie View Post
    Having some issues with a keyfob not registering with the Bosch Sol 3000 panel. Have gotten one registered under location 301 which operates alarm away/stay/panic/garage door. The second remote that came with the WE800EV2 kit won’t register with the panel no matter what I try. Tried different keyfob locations (I.e. 302, 309, 321) and it always gives an error beep.

    This is what I’ve been doing: mastercode+1 away > 302 away > away again > (keypad zones flash) press button 1 or 2 on remote > (keypad displays last digit of keyfob code) away then it does the long error beep. Normally I would press away twice and it would register no problems.

    Have tried deleting all keyfobs and reprogaming them in and have the same issue, one works other doesn’t. The garage operates fine using button 3 even though it’s not able to arm the system (just to point out that the remote works)).

    Lost
    Had one recently where 2 remotes didn't program in, tried to default panel and all still didn't work.

    Ended up getting a new receiver and it worked straight away, sometimes things are faulty out of the box for whatever reason.

  • Tags for this Thread

    Bookmarks

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •