Page 2 of 2 FirstFirst 12
Results 21 to 25 of 25

Thread: Ace Tone Guitar Amplifier

  1. #21
    Senior Member
    bob_m_54's Avatar
    Join Date
    Jan 2011
    Location
    Newcastle, Australia
    Posts
    1,577
    Thanks
    703
    Thanked 713 Times in 454 Posts
    Rep Power
    375
    Reputation
    11418

    Default

    Quote Originally Posted by loopyloo View Post
    They become scratchy when the internal wiper starts to wear through the carbon track.
    Or when the carbon track has contamination on it, especially from the wrong kind of lube, and when the wiper tension gets too soft.

  2. The Following User Says Thank You to bob_m_54 For This Useful Post:

    loopyloo (21-06-18)



  • #22
    Senior Member

    Join Date
    Feb 2008
    Location
    Mid North Coast NSW . Australia
    Age
    62
    Posts
    1,876
    Thanks
    1,085
    Thanked 351 Times in 237 Posts
    Rep Power
    290
    Reputation
    4937

    Default

    Quote Originally Posted by bob_m_54 View Post
    Or when the carbon track has contamination on it, especially from the wrong kind of lube, and when the wiper tension gets too soft.
    Yep all true.

  • #23
    Senior Member
    nomeat's Avatar
    Join Date
    Jan 2008
    Location
    Commonly found in a pantry or the bottom of a fridge, searching for grains, fermented or distilled
    Posts
    4,118
    Thanks
    1,111
    Thanked 1,974 Times in 1,206 Posts
    Rep Power
    927
    Reputation
    32978

    Default

    Quote Originally Posted by loopyloo View Post
    No nothing's mixed up at all.
    Pots DO need lubrication. The carbon element in a pot is quite hard and is a poor lubricant. Using a light lubricant does not affect the electrical characteristics of a pot (or switch) except to enhance the conductivity between contacts. This has been proven with lower and much more stable millivolt readings.
    Inox is not like an oil and it never dries out. WD40 will clean a pot but when it drys it leaves crystals on the surface which add to the wear factor. I too would not use oil in a pot.

    Look here :





    If you had used Inox on those pots in the studio, they might have thanked you.
    There are certain pots that do not have a graphite based resistive track that may require a special lubricating surface including the wire wound pots mentioned in your links but graphite is an excellent lubricator.
    I am not talking about the bearing grease in a pot or the inner conductive metallic ring.

    Inox (I use the standard MX3) IS an oil, so is Lanolin but firmer at room temp, but I doubt that is the main ingredient and you must be related to the inventor to know that because just like Coca cola and WD-40 nobody knows what is in it, despite the B.S. found on the Internet.
    You will not find the composition of MX3 on the official Inox site. They have a special Lanolin based grease but I doubt that is what you are talking about.

    So like you said above I will also not use oil (or grease) in a carbon pot.

    In the 40 odd years I have been servicing electronic equipment I never had and have always done very well.
    If a pot could not be successfully cleaned then it got replaced and cleaners were mostly used as a temporary measure anyhow. If I did a job for a customer, scratchy pots and sockets were ALWAYS replaced.


    ...and while we are at disposing myths here is for entertainment something I found about WD-40:
    Last edited by nomeat; 21-06-18 at 06:26 PM.
    $$$...Welcome to Australia where corruption is legalized...$$$

    The only group that does not have a lobby is the middle income taxpayer.

  • The Following User Says Thank You to nomeat For This Useful Post:

    loopyloo (22-06-18)

  • #24
    Junior Member
    Join Date
    Sep 2012
    Posts
    156
    Thanks
    1
    Thanked 40 Times in 36 Posts
    Rep Power
    94
    Reputation
    715

    Default

    Seems different caus!es for scratchy pootsI. I think oxidisation features big.Thing is though that Inox works.Had Pana plasma about 2 yrs ago with half screen b/w roll pic. Removed many plugs inside used Inox replugged perfect pic still 2 yrs on. My Inox has PTFE added. Point is this STUFF WORKS! AND OBVIOUSLY prevents. Oxidisation reoccurring!

  • #25
    Senior Member
    bob_m_54's Avatar
    Join Date
    Jan 2011
    Location
    Newcastle, Australia
    Posts
    1,577
    Thanks
    703
    Thanked 713 Times in 454 Posts
    Rep Power
    375
    Reputation
    11418

    Default

    Just don't spray it in pots LOL

  • Page 2 of 2 FirstFirst 12

    Bookmarks

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •