Page 5 of 8 FirstFirst 12345678 LastLast
Results 81 to 100 of 146

Thread: Kenwood Food Mixer - No Power - Mint Cond - Dead.

  1. #81
    Premium Member

    Join Date
    Jan 2010
    Posts
    1,077
    Thanks
    632
    Thanked 306 Times in 180 Posts
    Rep Power
    300
    Reputation
    4620

    Default

    Right.
    nomeat - no 240vac, got it! And the CRO Probe was on 10x.

    Tested (out of board), the .33uf cap and it reads .031uf.
    The R205 read 51Ω
    The Cxxx 470uf 16v - read 454uf
    Also tested the yellow cap at the A and N and it read .99nF (had 1.0uF).

    On the front board - off board - I tested C105 as Skepticist mentioned and it read 9.9nf.


    Also R104 read 99Ω.

  2. The Following 2 Users Say Thank You to GT250 For This Useful Post:

    Skepticist (14-02-19),Uncle Fester (14-02-19)



  • #82
    Banned

    Join Date
    Jan 2017
    Location
    still above ground level
    Posts
    1,779
    Thanks
    5,562
    Thanked 1,964 Times in 714 Posts
    Rep Power
    0
    Reputation
    35657

    Default

    who enjoying this ???? I am

  • The Following 4 Users Say Thank You to hinekadon For This Useful Post:

    GT250 (15-02-19),loopyloo (15-02-19),Skepticist (14-02-19),Uncle Fester (14-02-19)

  • #83
    Premium Member
    Skepticist's Avatar
    Join Date
    Apr 2009
    Posts
    1,139
    Thanks
    714
    Thanked 670 Times in 525 Posts
    Rep Power
    475
    Reputation
    12780

    Default

    Double checked that 0.33uF cap?
    If it's only 1/10 of the marked capacitance (0.031uF) then that's the culprit right there with 10 x the intended reactance
    All the other components are well within their tolerance range
    Last edited by Skepticist; 14-02-19 at 05:10 PM.

  • The Following 3 Users Say Thank You to Skepticist For This Useful Post:

    GT250 (15-02-19),hinekadon (14-02-19),Uncle Fester (14-02-19)

  • #84
    Senior Member
    Uncle Fester's Avatar
    Join Date
    Jan 2008
    Location
    Commonly found in a pantry or the bottom of a fridge, searching for grains, fermented or distilled
    Posts
    6,405
    Thanks
    2,289
    Thanked 4,414 Times in 2,517 Posts
    Rep Power
    2046
    Reputation
    81778

    Default

    0.031µF !!! What a difference taking it out of board and a '0' makes


    [QUOTE]Also tested the yellow cap at the A and N and it read .99nF (had 1.0uF).[/QUOTE]

    Are you sure? It is much smaller than the 0.33µF but must endure the same mains voltage. I would have expected 0.1µF from that size.
    Last edited by Uncle Fester; 14-02-19 at 05:34 PM.
    Update: A deletion of features that work well and ain't broke but are deemed outdated in order to add things that are up to date and broken.
    Compatibility: A word soon to be deleted from our dictionaries as it is outdated.
    Humans: Entities that are not only outdated but broken... AI-self-learning-update-error...terminate...terminate...

  • The Following 3 Users Say Thank You to Uncle Fester For This Useful Post:

    GT250 (15-02-19),hinekadon (14-02-19),Skepticist (14-02-19)

  • #85
    Premium Member
    Skepticist's Avatar
    Join Date
    Apr 2009
    Posts
    1,139
    Thanks
    714
    Thanked 670 Times in 525 Posts
    Rep Power
    475
    Reputation
    12780

    Default

    I assumed that should been .99uF but it pays to make certain always

  • The Following User Says Thank You to Skepticist For This Useful Post:

    hinekadon (14-02-19)

  • #86
    Premium Member

    Join Date
    Jan 2010
    Posts
    1,077
    Thanks
    632
    Thanked 306 Times in 180 Posts
    Rep Power
    300
    Reputation
    4620

    Default

    Sorry guys...
    Yeah, Typos. Big cap was 0.31uF and the little yellow one was 0.1uF.

    It's annoying to be checking all these items (that normally should be), responsible for the no power, yet they are reading ok.

    How about I order a PS board $48 and see ?

  • The Following User Says Thank You to GT250 For This Useful Post:

    Skepticist (15-02-19)

  • #87
    Premium Member
    Skepticist's Avatar
    Join Date
    Apr 2009
    Posts
    1,139
    Thanks
    714
    Thanked 670 Times in 525 Posts
    Rep Power
    475
    Reputation
    12780

    Default

    That 0.33uF X2 cap is about the only component that could throttle the voltage without being completely obvious so it would be worth replacing it as they only cost a dollar or two just to be certain it's not somehow intermittent or voltage/temperature related. Until the actual cause of failure is located there can be no certainty of the correct action required to fix it.

    Have you tried running the motor to see if its in good shape?
    I know it 'moved' when you bridged the triac terminals briefly but it would be very inconvenient to spend $100 or more replacing all the electronics only to find the motor needs replacing as well.

  • The Following User Says Thank You to Skepticist For This Useful Post:

    GT250 (16-02-19)

  • #88
    Premium Member

    Join Date
    Jan 2010
    Posts
    1,077
    Thanks
    632
    Thanked 306 Times in 180 Posts
    Rep Power
    300
    Reputation
    4620

    Default

    OK, I'll source a 0.33uF.
    Is this one ok on eBay 253811263401 - different colour and brand though.

    What seems to be an original is from the UK (got to buy 2 qty), $15 delivered. 183509298121

    Alibaba $US .01cents each!! 100qty though, LOL!!!

    Anyone got one of these in their drawers...?

  • #89
    Premium Member
    Skepticist's Avatar
    Join Date
    Apr 2009
    Posts
    1,139
    Thanks
    714
    Thanked 670 Times in 525 Posts
    Rep Power
    475
    Reputation
    12780

    Default

    The Ebay one should do the job - has all the right numbers. The only potential issue is the physical size but it will prove/disprove the existing cap as the problem at least.
    Element14 has a fair selection of X2 caps and way cheaper but the issue is the postage cost which is waived if your order is over a certain figure ($35 I think). RS components might be better for a small order like this (fast too)

    Element14 range:
    They deliver in a day or 2 if the component is in local stock, somewhat longer if it comes from an overseas warehouse
    Last edited by Skepticist; 15-02-19 at 06:12 PM.

  • The Following User Says Thank You to Skepticist For This Useful Post:

    GT250 (16-02-19)

  • #90
    Senior Member
    fandtm666's Avatar
    Join Date
    Jan 2008
    Posts
    5,502
    Thanks
    244
    Thanked 990 Times in 465 Posts
    Rep Power
    1189
    Reputation
    40447

    Default

    if you are in Sydney or know some one they can get one from wagners $2





    Last edited by fandtm666; 15-02-19 at 07:44 PM.

  • The Following 2 Users Say Thank You to fandtm666 For This Useful Post:

    GT250 (16-02-19),hinekadon (16-02-19)

  • #91
    Premium Member
    Skepticist's Avatar
    Join Date
    Apr 2009
    Posts
    1,139
    Thanks
    714
    Thanked 670 Times in 525 Posts
    Rep Power
    475
    Reputation
    12780

    Default

    Tried RS components, delivery is free and next day but you have to buy 10 caps so $17 including GST
    Element14 will supply 1 cap next day but shipping charge (vie Toll) is $13 unless you order over $45 worth of components so 10 caps from them is all up around $23 inc GST, or 1 will cost near $15.

    Pressure is on to buy a bag of stuff

  • The Following 2 Users Say Thank You to Skepticist For This Useful Post:

    GT250 (16-02-19),hinekadon (15-02-19)

  • #92
    Premium Member

    Join Date
    Jan 2010
    Posts
    1,077
    Thanks
    632
    Thanked 306 Times in 180 Posts
    Rep Power
    300
    Reputation
    4620

    Default

    Many thanks for the links people.

    I'll order one today and hopefully it will arrive early next week.

    Cheers.

  • The Following User Says Thank You to GT250 For This Useful Post:

    hinekadon (16-02-19)

  • #93
    Premium Member

    Join Date
    Jan 2010
    Posts
    1,077
    Thanks
    632
    Thanked 306 Times in 180 Posts
    Rep Power
    300
    Reputation
    4620

    Default

    The new cap arrived today.
    Ordered Sat afternoon by phone - told to be processed on Monday. Arrived Friday afternoon.

    So tomorrow morning, I'll pop it in and see if Skepticist is correct...
    Obviously, I can't keep ordering these single components bit by bit due to sheer $cost and time. The cap read 'ok' anyway. However, I am lead by the experts
    I've got the screws, bolts, bits and bob's everywhere - going to be a challenge to put it back in one piece LOL!!!

    nomeat: Yes, I have left the 'probe sticks' on the PIC for future testing

  • The Following 2 Users Say Thank You to GT250 For This Useful Post:

    hinekadon (22-02-19),Skepticist (22-02-19)

  • #94
    Premium Member
    Skepticist's Avatar
    Join Date
    Apr 2009
    Posts
    1,139
    Thanks
    714
    Thanked 670 Times in 525 Posts
    Rep Power
    475
    Reputation
    12780

    Default

    Not many components in that simple power supply and that cap has got to be the major suspect being the most critical part of it. The other parts (zener, diode, resistor) are easily obtained if it comes down to that.

    Fingers crossed

  • The Following User Says Thank You to Skepticist For This Useful Post:

    GT250 (23-02-19)

  • #95
    Premium Member

    Join Date
    Jan 2010
    Posts
    1,077
    Thanks
    632
    Thanked 306 Times in 180 Posts
    Rep Power
    300
    Reputation
    4620

    Default

    It Works! Well, sort of....

    Put the new cap in and when I slid the power slide to the first position the motor started spinning!!! YIPPEE. However, it starts and stops

    Spins up, then winds down, spins up, winds down....
    In the video (for some reason no sound plays), you can't hear the motor starting up and spinning down - which I assume is a loss of power.

    I noticed a spark from the (I think), commutator, every time it started the motor. So you will have to use your imagination as the vruumm, deeerrrr, vruumm, deeerrr, cycle as you can time it to the copper windings turning.





    So why would a cap @0.316uF not do anything but a new cap @0.334uF make it work? Seem such a small difference.
    Last edited by GT250; 23-02-19 at 12:22 PM.

  • The Following 3 Users Say Thank You to GT250 For This Useful Post:

    hinekadon (23-02-19),Skepticist (23-02-19),Uncle Fester (23-02-19)

  • #96
    Banned

    Join Date
    Jan 2017
    Location
    still above ground level
    Posts
    1,779
    Thanks
    5,562
    Thanked 1,964 Times in 714 Posts
    Rep Power
    0
    Reputation
    35657

    Default

    thats interesting gt that means that the triac is firing and stopping the firing again repeat /repeat we will have to get to the bottom of this , then you can make some scones ????lol the cap is charatistic of a fail cap so dont worry about that , have to make sure the 5v supply isnt falling off next step which will turn off the triac and produce the shown effect .

  • The Following 2 Users Say Thank You to hinekadon For This Useful Post:

    Skepticist (23-02-19),Uncle Fester (23-02-19)

  • #97
    Senior Member
    Uncle Fester's Avatar
    Join Date
    Jan 2008
    Location
    Commonly found in a pantry or the bottom of a fridge, searching for grains, fermented or distilled
    Posts
    6,405
    Thanks
    2,289
    Thanked 4,414 Times in 2,517 Posts
    Rep Power
    2046
    Reputation
    81778

    Default

    Maybe it just needs a load for the speed regulator to work. You mentioned the first speed, how about the others?
    Otherwise check the wiring carefully (continuity test all the way to the PIC board), focus on the hall sensor and that it's positioning hasn't moved, no soldering splatter on the PCBs when you replaced the cap and other parts.
    Last edited by Uncle Fester; 23-02-19 at 01:07 PM.
    Update: A deletion of features that work well and ain't broke but are deemed outdated in order to add things that are up to date and broken.
    Compatibility: A word soon to be deleted from our dictionaries as it is outdated.
    Humans: Entities that are not only outdated but broken... AI-self-learning-update-error...terminate...terminate...

  • The Following 2 Users Say Thank You to Uncle Fester For This Useful Post:

    hinekadon (23-02-19),Skepticist (23-02-19)

  • #98
    Premium Member
    Skepticist's Avatar
    Join Date
    Apr 2009
    Posts
    1,139
    Thanks
    714
    Thanked 670 Times in 525 Posts
    Rep Power
    475
    Reputation
    12780

    Default

    Breakthrough at last
    The commutator looks a bit scored in the video and that's easily remedied if you want to dismantle the motor.
    The 'pulsing' could be due to the type of speed control it uses and running it with no load
    IE the PIC fires the triac until the hall sensor indicates the right speed then cuts the power until the speed falls below the set threshold then applies power to accelerate the rotor again. With no load (like a batch of cake mix or whatever) the rotor is accelerating above the speed setting.

    Maybe try mixing a batch of scones or just a bowl of water with it to see if it's more stable in operation on various speed settings

  • The Following 2 Users Say Thank You to Skepticist For This Useful Post:

    hinekadon (23-02-19),Uncle Fester (23-02-19)

  • #99
    Premium Member
    Skepticist's Avatar
    Join Date
    Apr 2009
    Posts
    1,139
    Thanks
    714
    Thanked 670 Times in 525 Posts
    Rep Power
    475
    Reputation
    12780

    Default

    If you have access to an ESR capacitor tester it might reveal the problem but there's no doubt now that the original cap has major issues.

    Only the lowest speed setting was mentioned - does the motor speed change with different settings?
    Last edited by Skepticist; 23-02-19 at 01:20 PM.

  • The Following User Says Thank You to Skepticist For This Useful Post:

    hinekadon (23-02-19)

  • #100
    Premium Member

    Join Date
    Jan 2010
    Posts
    1,077
    Thanks
    632
    Thanked 306 Times in 180 Posts
    Rep Power
    300
    Reputation
    4620

    Default

    Ok.
    There's no more 240VAC running around the whole thing. I tested a few places on the PIC board side that were 240VAC before, now there isn't - but I'm still going to be careful

    The probes on the PIC (nomeat), are now reading 4.8VDC

    The Hall sensor hasn't seemed to move It's glued in and the PCB board is located by two big bolts to the motor housing. Can I move it manually when the motors going without damaging anything?

    When I put load on the rotating head it doesn't' prevent the stop/start.

    When I move the power slide up the motor does spin with more power (greater revs), but then still stops, then restarts...

  • The Following User Says Thank You to GT250 For This Useful Post:

    hinekadon (23-02-19)

  • Page 5 of 8 FirstFirst 12345678 LastLast

    Bookmarks

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •