Results 1 to 9 of 9

Thread: Gearbox reduction

  1. #1
    Premium Member RedXT's Avatar
    Join Date
    Mar 2008
    Posts
    420
    Thanks
    227
    Thanked 123 Times in 67 Posts
    Rep Power
    201
    Reputation
    1944

    Default Gearbox reduction

    Got a RC 4 x 4 for my grand kid but it goes too fast and I need to slow it down. Anyone modified gearing on something like this
    or is it better to get a slower revving motor if possible. The main output shaft in the middle is the drive output to front and back



    cheers thomo



Look Here ->
  • #2
    Premium Member
    gulliver's Avatar
    Join Date
    Jan 2008
    Age
    74
    Posts
    1,094
    Thanks
    6,713
    Thanked 274 Times in 189 Posts
    Rep Power
    260
    Reputation
    3692

    Default

    Couldn't you just reduce he voltage?

  • #3
    Premium Member
    wotnot's Avatar
    Join Date
    Nov 2019
    Posts
    659
    Thanks
    208
    Thanked 434 Times in 273 Posts
    Rep Power
    201
    Reputation
    8690

    Default

    Bought similar for my young nephew, and after doing a bit of homework ended up buying one with a speed limit control (learners mode) built in. That's a pretty good premise because A> it's easier that swapping cogs, and B> as the driver skill increases you don't have to recog ; just turn the motor up. It would depend on the exact model as if there's any ratio changes you can make anyway (for a lot the answer is no). but engine speed control make more sense imho

  • #4
    Premium Member
    hinekadon's Avatar
    Join Date
    Jan 2017
    Location
    still above ground level
    Posts
    1,456
    Thanks
    3,829
    Thanked 1,580 Times in 580 Posts
    Rep Power
    649
    Reputation
    27977

    Default

    its a dc motor so you can cut back the volts use a mosfet best way i can see to make it easy don
    are you a self appointed hypocrite sheriff or just a nasty person

  • The Following 2 Users Say Thank You to hinekadon For This Useful Post:

    gulliver (11-02-20),RedXT (10-02-20)

  • #5
    Premium Member RedXT's Avatar
    Join Date
    Mar 2008
    Posts
    420
    Thanks
    227
    Thanked 123 Times in 67 Posts
    Rep Power
    201
    Reputation
    1944

    Default

    thanks people for some advice, it does have variable throttle, and a dial on the controller to slow it down but it is still a bit quick at the moment.
    He follows his old man and has to tow everything and thats really the problem it doesnt have enough grunt.
    The boat is not too bad but the van is a bit heavy



    I might have to start from scratch and make a 4 x 4 to

    Thanks Thomo

  • #6
    Premium Member
    wotnot's Avatar
    Join Date
    Nov 2019
    Posts
    659
    Thanks
    208
    Thanked 434 Times in 273 Posts
    Rep Power
    201
    Reputation
    8690

    Default

    ...the bottom-most circuit using a pair of 555 timers ...whole article is a good read on the topic really.

  • The Following User Says Thank You to wotnot For This Useful Post:

    RedXT (11-02-20)

  • #7
    Senior Member

    Join Date
    May 2018
    Posts
    1,597
    Thanks
    348
    Thanked 1,407 Times in 657 Posts
    Rep Power
    632
    Reputation
    27714

    Default

    What about something like these DC speed Controllers?
    I have a heap of them on different things and found them to be very reliable and take a lot more amps than their ratings. Being PWM they will reduce the speed without reducing the motor torque which if he wants to play trains with the things would be ideal.

    You could build it into the body of the car and remove the knob if you want and adjust the thing with a small screwdriver through a hole.
    There are different versions of the things in different amp ratings so you could get what ever you needed but the 10A versions are pretty cheap anyway.

    -SOME- of the Ac versions work on DC as well if you need a lot of power capacity. I have one on a solar feed for limiting DC through a heating element.








  • The Following User Says Thank You to george65 For This Useful Post:

    RedXT (11-02-20)

  • #8
    Premium Member RedXT's Avatar
    Join Date
    Mar 2008
    Posts
    420
    Thanks
    227
    Thanked 123 Times in 67 Posts
    Rep Power
    201
    Reputation
    1944

    Default

    Quote Originally Posted by george65 View Post
    What about something like these DC speed Controllers?
    I have a heap of them on different things and found them to be very reliable and take a lot more amps than their ratings. Being PWM they will reduce the speed without reducing the motor torque which if he wants to play trains with the things would be ideal.

    You could build it into the body of the car and remove the knob if you want and adjust the thing with a small screwdriver through a hole.
    There are different versions of the things in different amp ratings so you could get what ever you needed but the 10A versions are pretty cheap anyway.

    -SOME- of the Ac versions work on DC as well if you need a lot of power capacity. I have one on a solar feed for limiting DC through a heating element.








    Thanks George I think I have one of these or similar around somewhere

  • #9
    Premium Member

    Join Date
    Jan 2008
    Posts
    4,210
    Thanks
    5,597
    Thanked 4,052 Times in 1,720 Posts
    Rep Power
    1238
    Reputation
    47361

    Default

    PWM (Pulse Width Modulation) is by far the best way, as this method maintains the motor's torque, unlike voltage reduction.

  • Bookmarks

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •