Results 1 to 5 of 5

Thread: Bosch 2000 - RSC+ app on iphone

  1. #1
    Junior Member
    Join Date
    Aug 2020
    Posts
    2
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Reputation
    10

    Default Bosch 2000 - RSC+ app on iphone

    Hi,

    I have bosch 2000, i need arm, disarm and open/close garage door via RSC+ app on iphone, which device i need to buy to connect to panel

    Thanks



Look Here ->
  • #2
    Senior Member secure's Avatar
    Join Date
    Jan 2008
    Location
    W.A
    Posts
    907
    Thanks
    156
    Thanked 146 Times in 133 Posts
    Rep Power
    276
    Reputation
    2409

    Default

    Bosch B426-M is the IP module for the app.

    Your panel board also needs to be version 2.0.0 firmware or above.
    Last edited by secure; 16-08-20 at 11:53 PM.

  • #3
    Junior Member
    Join Date
    Aug 2020
    Posts
    2
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Reputation
    10

    Default

    Thanks secure, and How to run connect cable from panel to garage door

  • #4
    Senior Member secure's Avatar
    Join Date
    Jan 2008
    Location
    W.A
    Posts
    907
    Thanks
    156
    Thanked 146 Times in 133 Posts
    Rep Power
    276
    Reputation
    2409

    Default

    I'm not sure, as I haven't linked them to garage door before. It's to do with how the output is programmed, to make it show up in the app.
    Possibly re-program the smoke output and link to a relay to trigger garage door.

  • #5
    Junior Member
    Join Date
    Jun 2016
    Posts
    62
    Thanks
    0
    Thanked 5 Times in 5 Posts
    Rep Power
    99
    Reputation
    110

    Default

    Quote Originally Posted by tom598 View Post
    Hi,

    I have bosch 2000, i need arm, disarm and open/close garage door via RSC+ app on iphone, which device i need to buy to connect to panel

    Thanks
    Done this at my house

    Run and fig 8 or 4 core cable from panel to garage door (most usually have options on the door motors).

    You need to use the onboard relay (output4) on the board which does the internal siren and use that for the garage door.

    Contacts will be COM and NO

    You then need to put the internal pieze on Output 2 and program output 2 to become what Output 4 was, or you could double with the external siren if you wanted too.


    In installer mode to get garage door working enter the following

    454 - 2 *#
    455 – 8*#
    456 – 3*#
    457 – 2*#
    458 – 0*#
    459 – 2*#

    960#

    Ensure the jumper pin is set to dry contact on the board itself , you should see a GND and 12V option.

    In the app if you click on outputs you should see "output 1" and if you click "turn on" should operate the relay.

    It works 90% of the time , if you don't see it go out and back into the app and should be there, also make sure the RSC app is up to date.

    Hope this helps.
    Last edited by Midnight1982; 25-08-20 at 11:00 PM.

  • Bookmarks

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •