mgcamd worked well
Can someone tell me which softcams work with Irdeto 1 ?
I'm aware that CCcam up to version 2.0.0 works, but what else ?
Look Here -> |
mgcamd worked well
make sure the spelling is correct in my one it was all in lower case once i sorted that out it was all good
as shown below extract of mg_cfg
# config files folder (softcam, autoroll, ignore/priority)
00 files in /var/keys
# 01 files in /tmp
T: { 00 }
notice the spelling all lower case
Hmmm, strange. I had it working straight after a reboot. Still using 1.30d.
However, when I had to restart the softcam due to whitey not working, whitey starts to work and I1 softkeys stop.
I use Scam 3x as the softcam and paste this,
#Optus Aurora C1
H: { 12 34 56 { 12 34 56 78 90 12 34 56 78 90 } } this is HSN and HMK
M: { 12 34 56 { 12 34 56 78 90 12 34 56 } } this is Prid10 and PMK10
in var/keys/irdeto
Get these details off a goldie in a phoenix using GGedit.
KK
Install newcamd 6.10b and create a file called ppua and put it into /var/scce. Newcamd then creates some other files, one of which holds the plain keys. If there is an EMK update it should handle that too (so no going back to a logger for new EMK).
Create the 'ppua' file (no extension) using notepad or similar and copy in the following:
0602:000000:00:0001XXXXXX:aa aa aa aa aa aa aa aa
0602:000000:00:00c3YYYYYY:bb bb bb bb bb bb bb bb bb bb
Just 2 lines is all.
XXXXXX is the provid aa's are the PMK
YYYYYY is the HSN and the bb's are the HMK
Should all be OK after that.
Thanks go to enf
kcsoft (23-10-09)
G'day KK,
I too use Scam because I have a 7025 and apparently newcamd is not 7025 compatible. But each time there is a EMK rollout, mine does not update. I have to get an EMK from a friendly logger and convert it manually to PMK then put that back in the irdeto file.
Does anyone know which other cams will AU with the correct details?
Thanks in advance,
spence
try making your AutoRoll.Key & SoftCam.Key are CHOMD 755 and newcamd will then update. I used to use newcamd 5.28 many moons ago with the ppau file in var keys with Ir1 details when playing around.
sorry to dig up this old thread but was just wanting ti know do you put provid id 10 in and also pmk 10 or just the prov id 00 and pmk 00 values
also i read that you must change the last two prov id values to 00 , is that correct , havent had much luck so far but im not giving up
just to answer my own question its the 10 values and works perfect , pretty cool
just for anbody else , no you dont
yea it look a bit confusing the way its laid out huh?
0602:000000:00:0001XXXXXX:aa aa aa aa aa aa aa aa
0602:000000:00:00c3YYYYYY:bb bb bb bb bb bb bb bb bb bb
Just 2 lines is all.
XXXXXX is the provid
aa's are the PMK
YYYYYY is the HSN and the
bb's are the HMK
I dont think that Prid 00 is of any use these days? might be wrong
i did change the last two values of the prov id to 00 and its humming along just fine ? maybe it wont update properly ?
Bookmarks