Results 1 to 7 of 7

Thread: D-LINK DI-524 router

  1. #1
    Junior Member
    Join Date
    Jan 2008
    Location
    vic
    Posts
    96
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    201
    Reputation
    10

    Default D-LINK DI-524 router

    Hi guys i have a D-LINK DI-524 wireless router iv had it for 2 years anyway woke up this morning finding i cant use the net on my pc thats connected with lan that the router had signed it with a automatic private ip address there is no default gateway ip to it should be 192.168.0.1 but nothing there i unpluged power to it for 1 min also did a reset with the reset button but no use i also chide to get into the router to change settings but wont do that to so dos anyone no what i should do like ill buy a new one if i have to but has this ever happened to so one to also the status and wlan leds flash to gather every 5secs cant remember if thats what they should be doing haven't looked at the thing for so long.



Look Here ->
  • #2
    Premium Member rob916's Avatar
    Join Date
    Apr 2008
    Location
    Bargara, Queensland.
    Age
    52
    Posts
    1,573
    Thanks
    49
    Thanked 75 Times in 36 Posts
    Rep Power
    250
    Reputation
    248

    Default

    Try
    disconnect power.
    hold reset button
    connect power
    wait 15 secs
    then release reset button.
    What happens if I press alt + F4?

  • #3
    Junior Member
    Join Date
    Jan 2008
    Location
    vic
    Posts
    96
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    201
    Reputation
    10

    Default

    hi rob916 did what you said the status and wlan led started flashing faster then the wlan led went out and the status led just keeped flashing fast then i turned it off and back on and it still dos the flashing every 5sec thing i have no idea whats gorn wrong with it its been working good for the last 2 years

  • #4
    Premium Member rob916's Avatar
    Join Date
    Apr 2008
    Location
    Bargara, Queensland.
    Age
    52
    Posts
    1,573
    Thanks
    49
    Thanked 75 Times in 36 Posts
    Rep Power
    250
    Reputation
    248

    Default

    sounds like it has died.
    try here for some info
    Anyone else have any ideas?
    Dailydeals have a linksys/cisco one for $59
    What happens if I press alt + F4?

  • #5
    Junior Member
    Join Date
    Feb 2008
    Age
    38
    Posts
    19
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Reputation
    10

    Default

    Download the firmware from for the DI-524 (Revision B)

    as rob advised earlier
    - unplug power
    - hold reset button down and plug power back in after 5 seconds
    - continue holding button for further 5 seconds
    - Set Static IP on your PC LAN adapter - 192.168.0.5 should be fine.. Subnet 255.255.255.0 and Gateway 192.168.0.1
    - Try log in to device - it should display a Recovery mode page.. load the firmware you downloaded to it.
    - Once complete, set LAN back to obtain IP and DNS to Auto Obtain and check to see if you receive an IP from the router. Power cycle for 5 seconds if you still can't to determine.

    if this fails email rma@dlink.com.au and advise them of your troubleshooting steps and request for an RMA.

  • #6
    Junior Member
    Join Date
    Nov 2008
    Age
    41
    Posts
    1
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Reputation
    10

    Default D-Link DI-524 router

    Try this site -->

  • #7
    Junior Member
    Join Date
    Jan 2008
    Location
    vic
    Posts
    96
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    201
    Reputation
    10

    Default

    hi b0rg3 thanks mate for finding that but still no luck i did what the guy said to do but the status light is to flash realy fast after you reboot your pc after you set the ip to what he put and turn power off to the router well your pc reboots i chide to log on to it but still no luck so i think its fu!K ill still play with it and see what happends ill let yous no tonight if i get it to work thanks again

  • Bookmarks

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •