Sounds like a logic fault ,when you say no signal do you mean no antenna connected?. I'm not sure if this is the model that has the digital board fault, if it is Philips do the exchange for $154.
hey guys I have a Phillips TV
Model Number 29PT2252/79R
Chassis Number LO1.1A
It works, turns on and sound all good with no signal input
BUT as soon as I hook up the A/V to it it turns off in about 5 seconds
I turn it back on and dies again in 5 seconds
But if I turn it on with out the video input just the audio it keeps going
Any suggestions ?????
Could it be the High voltage tuning caps near the flyback ???
HELP LOL
One more thing what does the Q7450 (BC857) surface mount transistor
it's up near the fly back side of things ???
Cheers
When you do things right, people won't be sure that you have done anything at all
Look Here -> |
Sounds like a logic fault ,when you say no signal do you mean no antenna connected?. I'm not sure if this is the model that has the digital board fault, if it is Philips do the exchange for $154.
LOL I know those sets your talking about and man are they Shite
This set gets pictures as soon as you connect a input to it but just turns off
When you do things right, people won't be sure that you have done anything at all
I worked on a Philips TV this week .It was like a birds nest of wires .
They always did do things different to everybody else.lol
Tell me about it remember the old wood grain TV's man they use to make the best TV's now they are just cheap out dated crap LOL
When you do things right, people won't be sure that you have done anything at all
Digital control board.Not familiar.
If it has an IO board , that or digi boad
Sometimes best not get involved .
Nah it's not one of those thank God as they use to be exchange for $350 from prime LOL
When you do things right, people won't be sure that you have done anything at all
Hi B4L, mate, did you forget we're philips agents
right lets get started
1. what did it come in for eg no go, screen probs what
2. what have you done so far
these sets dont have the SSB (small signal board) but could still be software
have you put it into SAM or service mode (on cust RC with tv in standby pres 062596 then "i", now you have to press quickly, all buttons MUST be press no later than 0.75/sec between presses, best to practice hitting the right numbers before trying on set), if so what errors were detected
Q7450 is a shut down switch driven by Q7561 which in turn is driven from the opto circuit which is controlled by 7520 PSU pwm controller
try that lot and we'll go from there!
post results B4L, we'll fix the bugger, philips are FUN!
When I explained to the guy what avatar I wanted, that wasn't what I meant!
ON FURTHER RESEARCH
replace
7461 bc337
7463 bc327
2455 47uf 63v
remove 2615 1nf cap off pin7 of 7602 eeprom
do all those first if unit still faults go into service mode (previous post) check for error confirm options are
176 247 193 168 236 212 044
any errors post them and then we'll go in depth LOL
we havent yet!
oh by the way, these f**ks have a piss arsed G2 prob, if not adjusted DEAD RIGHT/SPOT ON it will cause the same symptoms, try adjusting screen slightly
When I explained to the guy what avatar I wanted, that wasn't what I meant!
philips are FUN! You need to get out more mate LOL
I will have to dig up a remote i must have one here as it's been a while since a Phillips TV has left here working ROFL
When you do things right, people won't be sure that you have done anything at all
LOL i will try turning the G2 down 1st
When you do things right, people won't be sure that you have done anything at all
Well that was fun adjusted the g2 and the pic wouldn't stay on for more 1 second LOL
But with a bit of mucking around the pic is back but for how long i will let you know .
cheers
When you do things right, people won't be sure that you have done anything at all
do the mods i suggested, otherwise it WILL bounce on you!
When I explained to the guy what avatar I wanted, that wasn't what I meant!
What a phillips Tv bounce let me try be back in a tick mate
When you do things right, people won't be sure that you have done anything at all
the cap off the eeprom is a biggy, it causes ALL SORTS OF shite!
When I explained to the guy what avatar I wanted, that wasn't what I meant!
Looks like you were right about the fly back mate still going
I will do the other stuff you recommend just in case
When you do things right, people won't be sure that you have done anything at all
just put a vote in for you in the tech exxcel awards, but looks like the winner will be the one who promises the most, or bribes Z80
LOL
When I explained to the guy what avatar I wanted, that wasn't what I meant!
If you vote for me I will shave the rest of your cat for you mate
or I can give you some vouchers for "Advanced Hair" yeah yeah
When you do things right, people won't be sure that you have done anything at all
Bookmarks