what channels do you get ?
what provider bouquets do you get ?
Should be A, Austar, CH 9,Foxtel,OPT,Unkown
do you see foxtel help pics?
do you TVSN pics ?
Hey all,
I have been looking / reading / searching BUT
unless i missed a page or something cant find the answer to my query.
I have 3 x Dm's & whn I scan C1, I don't get any of the Aurora channels
not even the tuning channel.
anyone able to point me to the error of my ways ???
then i will tackle the autoroll etc
DM500s & Relook 400S Owner.. was now =
copy of ATV Flash for ATV Gen1
WTD : Sniper Elite for Wii - with Rifle if possible
RIP gw1, "LIFE MEMBER" u will be sadly missed
Look Here -> |
what channels do you get ?
what provider bouquets do you get ?
Should be A, Austar, CH 9,Foxtel,OPT,Unkown
do you see foxtel help pics?
do you TVSN pics ?
I wil need to recheck the actual bouquets.
but yes , I get the Fox help Expo, Tvsn etc.. the FTA ones..
DM500s & Relook 400S Owner.. was now =
copy of ATV Flash for ATV Gen1
WTD : Sniper Elite for Wii - with Rifle if possible
RIP gw1, "LIFE MEMBER" u will be sadly missed
Check you have all the necessary transponders for Optus C1
I am using PLI framebuffer so yours may be arranged differently
Menu-Setup-Satellites & transponders-Transponder Edit-E 156.0 Optus C1
on the right hand side you should have 20 Transponders listed
from 12305/30000/H to 12728/24450 V
Do you have this, or something like this
P.S What image are you using ?
strange all three machines are missing Aurora channels
Become a Premium Member and support the Austech Forum
most definately check your lnb fergs it has happened to me and for the life of me i couldnt work out what was wrong , the client thought his box was screwed also , but just a $10 lnb
Do a scan on a vert TP like 12407 V SR30000 fec 2/3 with NIT and that should get all the Aurora channels.
Leroy
Yes, thats the same as what I have on the scan.. I can get Fox help Expo / Tvsn etc
PLI Jade.. started with 21 Trnsponders, after a scan it found 28. with 116 services found on C1
LNB should be fine as i swaped between the hummy & to setup the dream.. NO worries on the hummy. scan with Dream & none...
Maybe its a Voltage thing ??? what should the correct V be for the dreams ??
LNB is 10700 dual out
OK been reading checking more etc ..
Its doesnt seem to be locking onto any V Tp's.. H are fine ..
DM500s & Relook 400S Owner.. was now =
copy of ATV Flash for ATV Gen1
WTD : Sniper Elite for Wii - with Rifle if possible
RIP gw1, "LIFE MEMBER" u will be sadly missed
Yep... thats what i was about to suggest.
As you should get 388 channels on a C1 scan, or there abouts.
Check your LNB is the correct skew
Swap LNBs to see if yours is rooted.
No special set-up changes needed for a DM, just tell it what LNB you have and go.
Increase Voltage can be ticked... doesn't seem to matter tho.
Use another box like Strong or Hummax just to check you dish/lnb etc
are the dreams really sensitive with skew ??
As its great on a hummy / openbox / XMS 520
I assume the multiswitch should not make any difference
LNB settings = 10700 all through ??
DM500s & Relook 400S Owner.. was now =
copy of ATV Flash for ATV Gen1
WTD : Sniper Elite for Wii - with Rifle if possible
RIP gw1, "LIFE MEMBER" u will be sadly missed
My dream isnt that fussy at all.... can go anywhere between 6 and 9 o'clock and it'll pull in 12.407V no probs. If you have a cheap signal meter with the LED for V/H... plug it in line and see if the dream is changing polarity. Check at BOTH ends of the coax too... if there is a fault it is more likely to show up at the LNB end.. i.e., Voltage drop. If the LNB works ok with other receivers sounds more like a nightmare than a dream.
upgrading to Premium soon LOL
fergs, did the 3 dm's come from the same supplier with image set up? Couldn't be as simple as a satellites.xml problem, could it?
while we are on simple - what setting against Voltage under satelite set-up ?
Should be H/V - not 14v or 18V?
what about swap over two cables coming into multiswitch and rescan - see if you have a dodgy cable ? switches have set H and V port whereas LNB both work both ...
(clutching at straws here mate) - but worth a try
Mmmmmm only getting H
Using a Multiswitch......
Hello
OK ..
thanks for all the hints & tips guys..
It WAS in my face all the time.. simple as voltage settings
i was changing & then going to different page or what ever but wasnt / didnt save
all good now, just have to see the "easiest" way to delete all these channels & do a fresh scan again on C1.
FTP into the box is easiest I assume..
whats the easies program , or ust any FTP will do ??
DM500s & Relook 400S Owner.. was now =
copy of ATV Flash for ATV Gen1
WTD : Sniper Elite for Wii - with Rifle if possible
RIP gw1, "LIFE MEMBER" u will be sadly missed
Speak engrish boy!
Just re scan
or use the remote to delete
or use dreamedit
Many ways to do the same thing.
Or if you use the search button, you will find some nice bouquets here already made up for you.
Well done.. good fix.
Use the 'Blue' button menu and edit etc bouquets from there.
I use Dreambox Control Centre. Pretty much does all you need. FTP, Telnet, Scripts, Re-Images, Backups and more...... A much developed tool similar to DM's own Dreamup software which only re-images
I can email to you if you like.. 7.6Mb so pm me if you cant find it on the web. sometimes call DCC also.
Or you can just download DCC from here
I got Dream Box Edit from here
will see how i go with it for now.
thanks all for your help.
DM500s & Relook 400S Owner.. was now =
copy of ATV Flash for ATV Gen1
WTD : Sniper Elite for Wii - with Rifle if possible
RIP gw1, "LIFE MEMBER" u will be sadly missed
Bookmarks