Phoenix with cccam help

[daki]

I've been trying to get cccam working with serial phoenix reader (purple one from sattronics). I'm running ubuntu and managed to get orange card working with infinity usb smartmouse reader, however it was freezing every 60 emcs, so I decided to try different reader. However no luck getting this bastard working. Below is my config, and there are settings that i've used for inifity and the ones i'm using now to get this going. Tried different frequencies, both switches on the programmer itself, and what not. Any help would be appriciated.

I've also set up newcs server but didn't want to run it untill i get this baby going, as it just doesn't go to my head why it doesn't work.

#****SERVER SETTINGS**********************************
SERVER LISTEN PORT : 12000^M
#ALLOW TELNETINFO: yes^M
ALLOW WEBINFO: yes^M
SHOW EXTENEDED CLIENT INFO: yes
WEBINFO USERNAME : cccam^M
WEBINFO PASSWORD : server^M
#TELNETINFO USERNAME :^M
#TELNETINFO PASSWORD :^M
#TELNETINFO LISTEN PORT : 16000^M
WEBINFO LISTEN PORT : 16001^M
ZAP OSD TIME :3^M
OSD USERNAME : cccam^M
OSD PASSWORD : server^M
OSD PORT :80^M
SHOW TIMING : yes^M
DEBUG : yes^M
#NEWCAMD CONF :no^M
#MINI OSD : yes^M
CAID PRIO FILE : /emu/cccam/CCcam.prio^M
#************************************************* ****

#****SERIAL READER SETTINGS****USB********************
#BOXKEY: /dev/ ** ** ** **
#SERIAL READER: /dev/ttyUSB0 smartreader
#SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB0 3570000
#CAMKEY: /dev/ttyUSB0 11 22 33 44 55 66 77 88^M
#CAMDATA: /dev/ttyUSB0 11 22 33 44 55 66 77 88 99 aa bb cc dd ee ff^M
#TRY ALL CHIDS: /dev/ttyUSB0
#SMARTCARD SID ASSIGN: /dev/ttyUSB1 0 {faa, 32c9}
#************************************************* ****

#****SERIAL READER SETTINGS****SERIAL*****************
BOXKEY: /dev/ ** ** ** **
#SERIAL READER: /dev/ttyS1
PHOENIX READER PATH: /dev/ttyS1
SMARTCARD CLOCK FREQUENCY: /dev/ttyS1 3570000
CAMKEY: /dev/ttyS1 00 00 00 00 00 00 00 00^M
CAMDATA: /dev/ttyS1 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00^M
#TRY ALL CHIDS: /dev/ttyS1
#SMARTCARD SID ASSIGN: /dev/ttyS1 0 {faa, 32c9}
#************************************************* ****

forgot to mention, most of the settings I'm getting following errors

17:48:17.735 CCcam: calculated EGT: 209 us
17:48:17.745 CCcam: nds card found(new type)
17:48:21.742 CCcam: card init fail

if it's not this then it just says failed to read a card.
cheers
daki

[novica]

maybe we have to ask F***** for that info.....lol

[gado]

A. Remove your boxkey from the post
B: Take out the 3570000 in your frequency line it will probably run and bit faster.
C: i think it wont work as your chipset on the com port it the problem. Get a sunix pci card and try again.
D: Buy a Smargo I sell them

[daki]

thanks admin.

thanks gado... I thought it might have been the pci card... any way of changing baud rates in ubuntu... seems like its always running at 38400 I think.