FastActivate ENG 09.01.2011 Version 1.8.0.3
&
AutoActivate ENG 09.01.2011 Version 1.5.0.3
All Version Mirrors:
Change log:
09.01.2011 - V 1.8.03 - Minor unpdate & latest meta.txt
After further testing the cameras are working. I just cannot access the settings
So that's fine.
FastActivate ENG 09.01.2011 Version 1.8.0.3
&
AutoActivate ENG 09.01.2011 Version 1.5.0.3
All Version Mirrors:
Change log:
09.01.2011 - V 1.8.03 - Minor unpdate & latest meta.txt
DND (11-01-11)
You must make setconfig.txt to \config directory
and make line bton, remove line btoff
TTSoff = switch TTS off
FMon = FMTransmitter on (for x10)
FMoff = switch auto enabled FM by some Emus again off, only for Device without FM, Mp3-Player not more available
btoff = disable BT, if you not need, save then a little more RAM
bton = if you not have BT enable it Button for Speedcams in Menu
noqfixdel = disable Quickfix erase after you have press reset, if you wonder where is gone qfixfiles normally
delgns = remove (Start,supend) old TMC-Data (gns/gnsdata)
delmap = delete each boot currentmap.dat
cleanflash= delete all from Flash what is possible (*.mac etc.), Settings lost
viewmsg = enable BootHelpmessages
nomsg = disable complete all BootHelpmessages
runclean = remove all unneeded Files to save RAM, since it is original not more include now as experimental
rm = remove a few additional Files (also for BT needed) to save RAM (experimental)
runcheck = check a few "important" Files, view config.txt for Result
changedtext.txt = you can change the Text on Status/Info Screen, write your own Text in the File
SDid.txt = write for each SD/Memory a other Number inside and you can for each use a own different Mainsetting
usesetting= use always Settings from SD, not the in Device itself saved Settings
Last edited by pietu; 11-01-11 at 12:32 AM.
DND (21-01-11)
hi.i appreciate the all sharing but i have an issue.i excatly did what the instruction says but then when i downloed the last version of the ozmap and copied them my device just opening and stay with the tomtom thing and nothing happens.what should i do pls help. the device is tomtom start..thanks
hi.i appreciate the all sharing but i have an issue.i excatly did what the instruction says but then when i downloed the last version of the ozmap and copied them my device just opening and stay with the tomtom thing and nothing happens.what should i do pls help. the device is tomtom start..thanks
what is that ozmap ???
Have followed all directions to install 860.3101 on TTOne New Edition using FastActivator 1.8, including patching TTHome 2.
When I connect the TT to the PC and run TTHome, TTHome tells me I have an incorrect version of the TomTom application installed on my device and wants to report the error to TomTom (which I ignore).
TomTom Home tells me there are no updates for my device.
If I select the "Operate my Device" option of the TTHome program, everything appears to be OK.
Show Version gives the following info:
Device: Device ID
App 8.562 (438269/040301) OS:1000, 32 Mb RAM, (Free 32.0 Mb), GPS v1.20, Boot 1.0012, Map: 'Australia860.3101' v860.3101, Language: English UK
But 'The Rub' is the TomTom will not load and display the map when disconnected from the PC. It 'hangs' at the Splash.bmp screen.
I would appreciate any advice/comments to resolve these probs.
The mapsettings.cfg file may be corrupt. Try the following steps:
1) Connect your TomTom to the pc.
2) Run the TomTom Home program and go to "Operate My Device".
3) In the menu, go to "Add Favorite" and add any new location to your Favorites.
4) Unplug your TomTom from the pc and power it on.
If the problem persists, try deleting the file mapsettings.cfg found in your map folder, which in your case is the folder named "Australia860.3101".
Last edited by lemonfish; 31-01-11 at 02:11 AM.
TomTom GO 730, Navcore 9.051c, 64Mb RAM, Australia 925.5412, Bootloader: 5.5250
TomTom ONE v1, Navcore 9.170SE, 32Mb RAM, Australia 925.5412, Bootloader: 5.5244
How can i patch my tomtom home with fastactive. i get an error when i click tomtom home in fast active, saying: "tomtom home profile DLL not found" i have the go 750 fast active 1.8 and i think the navcore is 9053? does that sound right? The tomtom home version is currently 2.8 Any help would be great. Thanks
Your navcore should be fine and you have the latest version of TomTom Home.
This error you're getting just means that FastActivate cannot find the directory of the DLL file it needs to be patched.
Even without patching Home, you should still be able to use Home and receive updates. You may or may not be able to use the function "Operate My TomTom" in Home, so please let us know if you can. All other functions should work.
TomTom GO 730, Navcore 9.051c, 64Mb RAM, Australia 925.5412, Bootloader: 5.5250
TomTom ONE v1, Navcore 9.170SE, 32Mb RAM, Australia 925.5412, Bootloader: 5.5244
I"ll check that that option out and let you know. everything else seems to be ok though. Thanks
Hi Lemonfish. i tried to operate my go in home and it came up with this error: you cannot use this map on this device: Australia-254. what does this mean, and how can i fix it? Thanks
When you first time use "operate my device" option TomTom HOME download profile files. when profile files is installed, shut down TomTom HOME and patch it with FastActivate Premium TomTom HOME button
then start tomtom HOME again and it works....
if you use .BAK and .ORI files and navcore is these files is eg. 8010, TomTom HOME download "wrong" profiles.
eg 860.3101 maps not works with it even if you patch it
Last edited by pietu; 03-02-11 at 07:53 PM.
what are profile files? sorry but not to familair with this
I found the folder; navcore 9053520930@tomtom.com now what do i do?
Last edited by pietu; 03-02-11 at 09:02 PM.
Bookmarks