Page 1 of 6 123456 LastLast
Results 1 to 20 of 122

Thread: How to run your gamma at a cool +3V - with a 'factory' mod

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Junior Member
    Join Date
    Mar 2008
    Posts
    142
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    200
    Reputation
    14

    Default How to run your gamma at a cool +3V - with a 'factory' mod

    Quote Originally Posted by marc133 View Post
    Hi just wondering if there had to be a mod made on a STRONG SATELLITE Receiver - 4658X used with a gamma?
    I've read that there had to be a mod with the Humax 5400Z Card reader to drop the voltage, to prevent overheating.
    Just wondering if something simmilar had to be done to the Strong box.
    Much Appreciated
    Yes there is a mod ...

    ... and no you don't need a resistor or diode or even a volt regulator to drop the 5V supply to the card to 3V ...

    ... many mods discussed here do the unthinkable ... as was already covered in another post by gw1 ... dropping voltage to the card alone without proper care of the interface electronics can 'break' your smartcard


    Quote Originally Posted by mickc View Post
    no mod needed on newer strongs
    ... not exactly true ...

    If we assume that gamma cards run of +3V - then even though they may indeed operate at +5V and be able to dissipate the 'heat' ... they are not running within their ideal specification that of +3V ...

    The card reader on the STRONG 4658X as well as many other receivers use a TDA8024 IC card interface ...



    ... the clever thing about this device is that it already has a +3V mode of operation ... by examining the data sheet (above link) we can see that pin 3 - when strapped to +5v will operate the card interface at 5V - if we GND pin 3 then the card interface will operate at +3V ...

    If we examine the card reader PCB on the 4658X - then we will see that pin 3 is at +5V - as expected ... to change the mode of operation of the card reader to +3V - we need to tie pin 3 to GND ...

    WARNING : No we don't just 'tie' pin 3 to GND ... we need to unsolder the pin - 'lift' it so it does not touch any other tracks ... and finaly 'tie' the naked pin 3 to GND ...

    See picture of completed mod ...

    If you do indeed make this mod - PLEASE check the voltage of the card reader - by inserting the 'rear' of your gamma - so that no contact is made to its landing pads ... just in case you 'botched' the mod ... you don't want to fry your gamma ...

    ... by inserting the card ... we trigger the micro contact of the reader socket and enable the 'voltage' to turn-on ... we can then measure between pins C1 and C5 which are clearly marked on the PCB ...

    GOOD LUCK ... and lets stop all of the 'he' said , 'she' said modify this resistor / add this diode type of mods ... the above IS in effect a FACTORY mod for +3V operation on all card readers utilizing a TDA8024 IC card interface ... so it can be applied to any receiver which uses this chip




  2. Look Here ->
  3. #2
    Junior Member
    Join Date
    Jan 2008
    Posts
    104
    Thanks
    0
    Thanked 5 Times in 4 Posts
    Rep Power
    201
    Reputation
    36

    Default

    Now that is a good pickup..

    Thanks for sharing it..

  4. #3
    Senior Member
    BillyGoat's Avatar
    Join Date
    Jan 2008
    Posts
    2,039
    Thanks
    845
    Thanked 470 Times in 242 Posts
    Rep Power
    340
    Reputation
    3754

    Default

    Nice work.
    Does the humax use the same chip?

  5. #4
    Senior Member
    BillyGoat's Avatar
    Join Date
    Jan 2008
    Posts
    2,039
    Thanks
    845
    Thanked 470 Times in 242 Posts
    Rep Power
    340
    Reputation
    3754

    Default

    Never mind.
    The answer is Yes.
    Thanks for the info.
    I might run it thru a switch so I can switch between the two voltages if needed.

  6. #5
    Senior Member
    weirdo's Avatar
    Join Date
    Jan 2008
    Posts
    5,458
    Thanks
    4,638
    Thanked 3,135 Times in 1,633 Posts
    Rep Power
    0
    Reputation
    29602

    Default

    Great stuff eyesee

  7. #6
    Senior Member
    best4less's Avatar
    Join Date
    Jan 2008
    Location
    Australia
    Posts
    7,684
    Thanks
    3,487
    Thanked 2,207 Times in 1,132 Posts
    Rep Power
    757
    Reputation
    15165

    Default

    Do you need that 100nf cap or should it be close enough

    Quote from the above PDF
    For reasons of VCC voltage accuracy, a 100 nF capacitor
    with an ESR < 100 mW should be tied to CGND near to
    pin VCC, and a 100 or 220 nF capacitor (220 nF is the best
    choice) with the same ESR should be tied to CGND near
    card reader contact C1.

    What voltage are you getting without the cap and is it
    stable enough for the card??

    Ohh and thanks nice find
    When you do things right, people won't be sure that you have done anything at all

  8. #7
    Junior Member
    Join Date
    Mar 2008
    Posts
    142
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    200
    Reputation
    14

    Default

    ... most component data sheets cover all aspects of device operation as specifically designed my manufacturers ... the TDA circuit as implemented by various card reader manufacturers may or may not follow specific datasheet guidelines ... reasons for this could be commercial (i.e. save a few $$ on a component you don't 'really' need to insert) ... or from a circuit point of view ... where a designer specifically chooses not to operate the device in a 'published' mode ...

    ... with regard to the Strong Card reader as used ... which is the basis of this post ... the circuit implemented is perfectly stable and operating within the 'design' parameters of Strong’s Card readers original design ...

    ... by changing the operation to +3V ... its not really necessary to add additional components specifically for this to function ...

    … all you have to do is take pin 3 to a GND .. I’ve chosen a good point … the GND side of a SMD cap next to the device … (see photo)

    .. after the mod .. the power to the card is +3V and stable ...

    One thing that I don't like about the Strong’s Card reader is the physical mechanism - the landing pads do not retreat and leave 'skid' marks on your card when inserted and removed multiple times ...

    The JayCar MKII had a 'retractable' landing pad mechanism - this can (I think) be purchased on its own ... and fitted to the Strong (a little skill in soldering and 'pin' manipulation required) ... then you can easily remove your card without causing undue 'wear' on the contacts ...

    ... perhaps .. my next project with the Strong




    Quote Originally Posted by best4less View Post
    Do you need that 100nf cap or should it be close enough

    Quote from the above PDF
    For reasons of VCC voltage accuracy, a 100 nF capacitor
    with an ESR < 100 mW should be tied to CGND near to
    pin VCC, and a 100 or 220 nF capacitor (220 nF is the best
    choice) with the same ESR should be tied to CGND near
    card reader contact C1.

    What voltage are you getting without the cap and is it
    stable enough for the card??

    Ohh and thanks nice find

  9. #8
    Senior Member CoopsOz's Avatar
    Join Date
    Mar 2008
    Location
    Canberra
    Posts
    819
    Thanks
    94
    Thanked 99 Times in 57 Posts
    Rep Power
    234
    Reputation
    607

    Default

    Will a goldie run at 3v?

  10. #9
    Junior Member
    Join Date
    Jan 2008
    Posts
    104
    Thanks
    0
    Thanked 5 Times in 4 Posts
    Rep Power
    201
    Reputation
    36

    Default

    A five minute mod on the Strong...now to see if the card runs cooler.

    Anyone know if the Dreamax DT470 uses the same reader chip?

  11. #10
    Junior Member
    Join Date
    Jan 2008
    Posts
    104
    Thanks
    0
    Thanked 5 Times in 4 Posts
    Rep Power
    201
    Reputation
    36

    Default

    Beautiful..

    Cool as a cucumber

  12. #11
    Junior Member
    Join Date
    Jan 2008
    Posts
    99
    Thanks
    2
    Thanked 0 Times in 0 Posts
    Rep Power
    201
    Reputation
    10

    Default

    If your strong has a ST8004 instead of the TDA the mod works the same as pin 3 is 3v/5v same as the TDA. The only difference is you will need to find a diffeent place for the earth as the board is slightly different.

    Cheers

    ktm200

  13. #12
    Junior Member
    Join Date
    Apr 2008
    Age
    40
    Posts
    182
    Thanks
    8
    Thanked 1 Time in 1 Post
    Rep Power
    201
    Reputation
    20

    Default

    Ok so you lift pin 3 up on the ic. Solder a piece of wire to the lifted pin.

    Then you solder the other end of the wire to the gnd.

    Im having problems deciding which part of that gnd point to solder to.

    Theres two sides. And they are separated by the board.

    Which side is the gnd?? Bottom side in relation to the desoldered pin, or the top side in relation to the top of the chip. Or do you solder it so it connects between both points?

  14. #13
    Member
    Join Date
    Jan 2008
    Location
    Here & There
    Posts
    293
    Thanks
    136
    Thanked 23 Times in 13 Posts
    Rep Power
    208
    Reputation
    63

    Default

    I did this mod on my friends strong 4658x a few days ago it has the ST8004 chip & the heat problem. Now his comments are that the card runs cooler in the box than it does out of the box.

    I think he's joking of course, thanks for the uncomplicated fix eyesee .

  15. #14
    Junior Member
    Join Date
    Feb 2008
    Posts
    173
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    202
    Reputation
    10

    Default

    Has anyone else got more pics of there finished mod?

  16. #15
    Junior Member
    Join Date
    Jan 2008
    Posts
    95
    Thanks
    0
    Thanked 1 Time in 1 Post
    Rep Power
    201
    Reputation
    15

    Default

    here ya go

  17. #16
    Junior Member
    Join Date
    Feb 2008
    Posts
    173
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    202
    Reputation
    10

    Default

    Quote Originally Posted by redmick View Post
    here ya go
    good stuff, I havnent yet done mine, need to get a solder iron...

  18. #17
    Junior Member
    Join Date
    Apr 2008
    Age
    40
    Posts
    182
    Thanks
    8
    Thanked 1 Time in 1 Post
    Rep Power
    201
    Reputation
    20

    Default

    also i have a multimeter here. and its saying its 6.4v...

    it cant be 6.4, im thinking it mm is screwed.

  19. #18
    Junior Member
    Join Date
    Jan 2008
    Posts
    104
    Thanks
    0
    Thanked 5 Times in 4 Posts
    Rep Power
    201
    Reputation
    36

    Default

    Lift the pin (make sure you get the correct one), and prepare a short piece of wire, stripped and presoldered.

    Use your ohmmeter to find a suitable earth point...measure between this point and the tuner, or the casing to ensure the point is connected to earth.

    Solder one end of the wire to the lifted pin, and the other to your selected earth point.

  20. #19
    Junior Member
    Join Date
    Apr 2008
    Age
    40
    Posts
    182
    Thanks
    8
    Thanked 1 Time in 1 Post
    Rep Power
    201
    Reputation
    20

    Default

    I have lifted the correct pin. Soldered a wire to it.

    i have followed the photo supplied. connected it to the bottom of the point called SC6..

    I have a 4653x. Where is the earth point? GND?

  21. #20
    Junior Member
    Join Date
    Jan 2008
    Posts
    104
    Thanks
    0
    Thanked 5 Times in 4 Posts
    Rep Power
    201
    Reputation
    36

    Default

    Quote Originally Posted by under- View Post
    I have lifted the correct pin. Soldered a wire to it.

    i have followed the photo supplied. connected it to the bottom of the point called SC6..

    I have a 4653x. Where is the earth point? GND?
    I'm not sure about the 4653, but if you check for continuity between sc6 and GND, you have done the job...

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •