Hi all,
I am having trouble setting my Hills HST2 for the VAST parameters.
I can see the signal strength but cannot lock onto the MER.
I have all the right parmeters and have installed the channel list that hills sent me.
Any advice would be good,
Thanks
Jack
8. Signatures or user profiles containing commercial advertising for any web sites or advertising commercial goods will be removed , as will your account if you persist in doing it. This does not apply to Premium Members. Advertising banners are not permitted in signatures by any member group. A small logo may be permitted but if deemed to be too big will be removed at Austech's discretion.
Look Here -> |
Is there a firmware upgrade that will allow me to read DVBS2 ?
8. Signatures or user profiles containing commercial advertising for any web sites or advertising commercial goods will be removed , as will your account if you persist in doing it. This does not apply to Premium Members. Advertising banners are not permitted in signatures by any member group. A small logo may be permitted but if deemed to be too big will be removed at Austech's discretion.
Your hardware needs to be capable.
Leroy
XCRUISER HDSR600HD twin sat and terrestrial receiver $OOS *
XCRUISER HDSR385 Avant - sold out$OOS UltraPlus DVB-T and DVB-S2 tuners $49 Remotes $OOS
Thanks Guys,
I will call Hills on Monday to clarify.
Cheers
Jack
8. Signatures or user profiles containing commercial advertising for any web sites or advertising commercial goods will be removed , as will your account if you persist in doing it. This does not apply to Premium Members. Advertising banners are not permitted in signatures by any member group. A small logo may be permitted but if deemed to be too big will be removed at Austech's discretion.
I have the manual here, it only does DVB and DSS.
Go to Google Maps and click “Get Directions.” Get directions leading from China to Taiwan, and look at instruction #48.
Thick as two bricks but wouldnt that meter find the Tune channel for C1 and once you have that locked in, wouldnt that do in the short term?
I stand unequivicably behind everything I say , I just dont ever remember saying it !!
Funny that govt endorsment for digital switchover installers approves the meter even tho it doesn't do DVBS2. All they wanted is a meter that does MER + BER. I got the ok for domestic,commercial and sat installation with that meter. Won't make much difference in my area tho as there are no VAST installs for me to do.
I wonder if they can run a tuning channel to optimise VAST but in DVBS.
Cheers,
Nando.
Go to Google Maps and click “Get Directions.” Get directions leading from China to Taiwan, and look at instruction #48.
Shows whoever approved that meter for VAST is as thick as me by presuming if you can tune one channel (Tune Channel on C1) thats all you need.
Last edited by gordon_s1942; 28-05-11 at 10:45 PM.
I stand unequivicably behind everything I say , I just dont ever remember saying it !!
Yes. I Agree, Having the tuning channel on DVBS would enable us all to fine tune the MER.
8. Signatures or user profiles containing commercial advertising for any web sites or advertising commercial goods will be removed , as will your account if you persist in doing it. This does not apply to Premium Members. Advertising banners are not permitted in signatures by any member group. A small logo may be permitted but if deemed to be too big will be removed at Austech's discretion.
easy peasy upgrade, just undo case screws, remove contents, insert new contents, replace screws and away you go.
OHHHH, did I mention it might cost near as much for the new innards as one bought new without a case ???
I stand unequivicably behind everything I say , I just dont ever remember saying it !!
I spoke to hills about this meter and they told me that i will not do DVBS2 and therefore cannot read the MER on VAST.
However they have a new meter available that will do DVBS2.
Cheers
Jack
8. Signatures or user profiles containing commercial advertising for any web sites or advertising commercial goods will be removed , as will your account if you persist in doing it. This does not apply to Premium Members. Advertising banners are not permitted in signatures by any member group. A small logo may be permitted but if deemed to be too big will be removed at Austech's discretion.
Bookmarks