weirdo (11-06-11)
I recently saw a thread on another forum detailing a problem with CAM units on a Vu+Duo, so i thought i'd test my collection on the Uno i am using and post the results here.
NB all the below cams have been tested and are working on my DM 7020 prior to testing on the Vu+Uno
====
ORIGINAL
seca aston black rev 1.03 NOT DETECTED
seca aston black rev 1.04 FULLY WORKING
viaccess black rev 1 NOT DETECTED
viaccess red rev 1 v484 (software ver 1.0.484 / application ver 1.08.003 ) FULLY WORKING
irdeto 2 ( loader ver 3.1 / softcell ver 2.26D ) FULLY WORKING
conax ( technicrypt - technisat cx ) software ver 26.1.5.0.6 interface ver 0x40 FULLY WORKING
magic / special cams
dragon module rev 2.06 with loader card ( predator 3.69 updated to pred 3.80 with loader card in Uno ) FULLY WORKING
dragon module rev 3.02 ( firecrypt ) = damaged body ( predator 3.69 updated to pred 3.80 with loader card in Uno ) FULLY WORKING
diablo (1) light rev 2.2 upgraded to 2.3 via software patch ( underworld 2.14 ) FULLY WORKING
diablo (1) light rev 2.2 ( not updated still 2.2 ) ( underworld 2.14 ) FULLY WORKING
icecrypt blue rev 2.01 NOT DETECTED
zeta orange rev 2.01 NOT DETECTED
matrix reloaded ( mr 1.082 ) HW 1.5 / loader 1.0 FULLY WORKING
matrix revolutions ( mrv 2.24 ) HW 1.5 / loader 1.0 FULLY WORKING
weirdo (11-06-11)
Look Here -> |
Nice collection of cams you have there dude. I didn't think that the Vu Uno had been released yet; I really am behind the times !
Hillsbysa (07-06-11)
well it would be a sad day if people started to sell off their boxes because softcam troubles, has any one tried to see if any hard cams can read the affected cards ?. i know the dragon cam could read the CAID 0961 sky uk NDS cards fine but so far i have not been able to get one to recognize my CAID 0963 sky uk NDS cards, even though the 0963 CAID heading is present in the predator firmware.
i can remember back to 2001 / 2002 when all the major European service providers beefed up their respective encryption. that left us all with black screens for over 2 years until another measure was found
XCRUISER HDSR600HD twin sat and terrestrial receiver $OOS *
XCRUISER HDSR385 Avant - sold out$OOS UltraPlus DVB-T and DVB-S2 tuners $49 Remotes $OOS
all you need to do with the CAID 0961 cards and the dragon cam is to enter the boxkey the card is paired to into the cam's settings via the setup menu on the box. takes only a few minutes. i had a 0961 sky uk card running very successfully for 5 years in my old DM7020 this way.
when i have time i'll take a few screen shots of the menu's etc for the dragon cam etc and post them up
aalyasseri (11-06-11),evilbrian (07-06-11),LeroyPatrol (07-06-11)
diablo 2 light ( diablo 1 rev 2.3 light updated to diablo 2 light via software patch ) ( Ipnosys034 ) FULLY WORKING
can a member of staff update the first post with this cam thanks.
Irdeto 1 freecam ( softcell ver 2.06 ) FULLY WORKING
T-rex twin module ver 1.0/4.1 ( firecrypt ) FULLY WORKING
irdeto 2 ( consumer / purple ) (softcell 2.21A / application ver 1.11.003) FULLY WORKING
Last edited by DUDE; 24-06-11 at 06:45 AM.
LeroyPatrol (17-07-11)
seca aston black rev 1.05 FULLY WORKING
cryptoworks ( phillips ) NOT DETECTED
T-rex super module rev 4.6 ( firecrypt ) ( PREDASAUR 2.40 ) FULLY WORKING
some new additions to the list.
Irdeto 1 freecam ( FreeCAM 2-019 ) FULLY WORKING
Magic Cam rev 1.05 P/N 8106/2003 NOT DETECTED
free-x tv rev 2.01 PRD-CAM0-0102 P/N 1250/2002 NOT DETECTED
I would also once again like to take this opportunity to thank SILVERFOX0786 and BASSETHOUND for their very generous donations of cam modules for inclusion into my collection.
many thanks again fellas it is really appreciated.
Bookmarks