JTAG xenon help

[dartronix]

Hi I got xenon xbox 360 i trying jtag useing tut
I got the nand read all ok
I have done all the steps in the end i got e79 error so i put the original nand back all comes to normal
Then i found the cracked nand bin file through google file named call xenon_1921hack.bin i flashed that same result getting e79 error

Any boddy able put in the right direction please
Thanks

[urban_s0ulja]

That's the wrong file you are trying to use.

[dartronix]

That's the wrong file you are trying to use.

can you please able tell me direct me where can i get the file please x bins is not working at the moment
Thanks

[dartronix]

anybody please

[loanrangiel]

anybody please

I would just use jtagtool as its a one stop program, no mucking around with other files required.

[dartronix]

hi loanrangiel can you please tell me how is that work please

[loanrangiel]

hi loanrangiel can you please tell me how is that work please

What type of nand read/write hardware are you using ? download jtag tool, then just select your console type, flash hardware (lpt or usb) and then read nand 3 times (select auto compare in settings) and when nands match write xellous to nand and then boot up to get cpu key. Then enter cpu key in jtag tool and then create image(bin file).

[loanrangiel]

Check this site, there is a download link down the page a bit.

[dartronix]

thanks i try to down load that xbins not working can i get it from other sources?
i am useing lpt

[loanrangiel]

thanks i try to down load that xbins not working can i get it from other sources?
i am useing lpt

Use the link i posted,in the box further down the page there is a download link.

[dartronix]

hi loanrangiel i have tryed that program still after wright xell i am getting e79 i have used the program to write the xell and turn on the xbox to see the keys
anything i am doing wrong?

[JasonC]

easyfreeboot is easy to use also

[loanrangiel]

easyfreeboot is easy to use also

EFB is ok too, i like jtag tool as you dont even need to disconnect the wiring to get the cpu key so you can read nand and write freeboot in less than 10 mins start to finish.

[JasonC]

nice
I must admit once I worked out how to get the cpu key from xell, it was pretty straightforward after that!

also to dartronix, if you can't get into xbins, you can find most (if not all) of the programs you need on the xbox forums if you look around

[dartronix]

thanks

[dartronix]

hi got more problems I have manage to install the write xell useing the jtag tool and manage to get the keys and create the freeboot bin file as per the program
And wrote the frreboot.bin to the xbox so far ok
But i get XeLLous v1.0 By Redline99 on the web (i tryed the xbox ip under tehinternet explorer)
This only works if i leave the jumber wire and 2 diode attached to the board
I am in the right track Any body able to help whats is the next thing to do please
Thanks

[loanrangiel]

hi got more problems I have manage to install the write xell useing the jtag tool and manage to get the keys and create the freeboot bin file as per the program
And wrote the frreboot.bin to the xbox so far ok
But i get XeLLous v1.0 By Redline99 on the web (i tryed the xbox ip under tehinternet explorer)
This only works if i leave the jumber wire and 2 diode attached to the board
I am in the right track Any body able to help whats is the next thing to do please
Thanks

Not sure what your trying to do but once you wirte freeboot to the nand thats it, you should be booting to freeboot image except when you use eject button to boot which brings you to xell/xellous.
The wiring stays in place otherwise you will get E79 error.

[dartronix]

so with out the cd rom what do i expect on the screen ?

[loanrangiel]

so with out the cd rom what do i expect on the screen ?

Without a dvd drive you will get the xell blue screen but you can boot freeboot without a drive you just need to start with a media remote or controller.

[dartronix]

with the media remote same thing booting message and keys etc..