There is a mgcamd plugin that you can use,
just have a newcamd.list file in the var/keys with the relevent info and have the cam autostart,
Hello again,
Quick question please?
If I was to hypothetically testing my box to experiment with it's capabilities, and trying to setup my ultra to receive a cardshare from elsewhere, do I only need to configure this area?
I have looked within it's present plugins and I have these details.
PLUGINs
Mclient
When I go into this setting I have a menu to put in this info
Client version 01
Server address_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Port 4828
User ID: dummy
Password: dummy
Is this all is needed, or should I be downloading something else as well? All mine has with plugins is
MCAS
KEDITOR
Mclient
Perhaps another plugin needs sourcing to test these areas?
If there is a nice known tutorial there, I'd be most appreciative of being provided with a dummy guide/link to read, as well as the second possibility of getting the box to also serve to another S9 Skybox afterwards.
I just have to keep experimenting with it, as otherwise my cobwebs just get thicker, and the box is seemingly being under used...I think.
Thanks
Look Here -> |
There is a mgcamd plugin that you can use,
just have a newcamd.list file in the var/keys with the relevent info and have the cam autostart,
viewer (04-08-11)
MCAS and MClient (which is loaded with the MCAS plugin) are used for LAN sharing or Home sharing.
To connect to connect to a server using the example settings above, you can use the MGcamd plugin as mentioned above or the XCamclient plugin. Xcamclient supports many different protocols including CCcam for the info above, Newcamd, and either can be used to connect to an oscam server.
You can edit/enter your CS details by running the Xcamconfigure plugin in the Plugin menu or you can FTP to /var/etc/xcamclient.conf using the login details
username: root
password: ultraplus
The line if it's newcamd for example
newcamd:192.168.1.50:12000:0/090b/0:userassword:0102030405060708091011121314
If it's a cccam line edit the cccam2 line in the config file.
You then need to start the xcamclient plugin and you'll see a window popup with the connection status when you run this.
Have fun!
Leroy
XCRUISER HDSR600HD twin sat and terrestrial receiver $OOS *
XCRUISER HDSR385 Avant - sold out$OOS UltraPlus DVB-T and DVB-S2 tuners $49 Remotes $OOS
viewer (04-08-11)
Thanks...so the McClient is only good for own to own (homelink type) communications I take it, and the MGcamd plugin /or the XCamclient plugin is for receiving from an external server...have I got that right?
Lastly, I assume "one" just finds the MGcamd or XCamclient plugin applicable that is written for an Ultraplus 980 only, puts this onto a thumb drive, and assumingly loads that information into the plugins folder somehow?
I will go a searching...still fighting cobwebs, but have a thick brush to sweep some off...thank you.
Ok,
Knobbled a copy from this post,
I see you say.."When you unzip the package you will see there is a plugin folder. Copy this to a usb memory stick and put it in your receiver. It will auto detect and prompt you to load the plugin. It's that easy!"
This procedure doesn't interupt/overwrite any other plugins that are running at the time does it, like MCAS etc?
Just being cautious...
Last edited by LeroyPatrol; 04-08-11 at 02:28 PM. Reason: more info
XCRUISER HDSR600HD twin sat and terrestrial receiver $OOS *
XCRUISER HDSR385 Avant - sold out$OOS UltraPlus DVB-T and DVB-S2 tuners $49 Remotes $OOS
viewer (04-08-11)
108.94 firmware and the MCAS from the 1.08.52 thread.
This is stable with my 5.4 austar card, so I can at least use it in my ultraplus after a bit of trial and error a while back...thus not wanting to upset it all.
I'll dig around then for the Xcamclient if you think that may be better
Last edited by LeroyPatrol; 04-08-11 at 03:11 PM.
XCRUISER HDSR600HD twin sat and terrestrial receiver $OOS *
XCRUISER HDSR385 Avant - sold out$OOS UltraPlus DVB-T and DVB-S2 tuners $49 Remotes $OOS
viewer (04-08-11)
I hate posing dumb questions..but...
I loaded MgCamd onto the Ultraplus, and then thought it would be when satrting that prog., that I would enter any necessary data there.
The program can only be changed ( as far as I can understand so far) via manual / auto start, but will not open to allow any data entry.
Am I supposed to notepad or something in the keys tab or similar?
XCRUISER HDSR600HD twin sat and terrestrial receiver $OOS *
XCRUISER HDSR385 Avant - sold out$OOS UltraPlus DVB-T and DVB-S2 tuners $49 Remotes $OOS
you need to make a newcamd.list file just using a text editor,
then FTP to the box in the var/keys directory
viewer (04-08-11)
Ultraplus 980HD Firmware V1.10.05. Any one know why I have no keys folder? I get as far as Var/ then I have Bin, Etc, Lib, share, www. Not sure where to put the newcamd.list file ? Do I need a different firmware/plugin version? Thanks
Last edited by worthp; 03-12-13 at 12:14 PM.
worthp (03-12-13)
Thanks Leroy, that was easy !
My newcamd.list file looks like this
CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = 192.168.1.1 20000 dummy dummy 10 02 13 04 15 06 17 08 01 10 11 12 13 14 lan server1
CWS_MULTIPLE = 192.168.1.2 20000:20005 dummy dummy 10 02 13 04 15 06 17 08 01 10 11 12 13 14 lan server2
CWS = #####.######.###.## 99999 user2 pass2 10 02 13 04 15 06 17 08 01 10 11 12 13 14
Mgcamd is started and set to Auto
card.client.conf file looks like this
#
# newcamd client
# 'cfgkey' is the config key (28bytes)
#newcamd:#####.######.###.## 99999 user2 pass2 10 02 13 04 15 06 17 08 01 10 11 12 13 14
#newcamd:127.0.0.1:32000:0/caid/mask:usernameassword:cfgKey
#newcamd:192.168.10.107:32000:0/0000/0000:dummy:dummy:0102030405060708091011121314
#newcamd:127.0.0.1:32000:0/0000/0000:dummy:dummy:0102030405060708091011121314
#
# gbox client
XcamClient started and set to Auto
Not working.....can you see anything obviously I have done wrong?
Many thanks.
Which emu are you trying to use? Mgcamd line missing a space between 17 and 08.
Looks like you have everything # out in xcamclient. Conf!
Leroy
XCRUISER HDSR600HD twin sat and terrestrial receiver $OOS *
XCRUISER HDSR385 Avant - sold out$OOS UltraPlus DVB-T and DVB-S2 tuners $49 Remotes $OOS
Thanks, not sure what you mean by EMU, sorry I'm a bit slow on it!
OK, when I start Xcamclient it says "starting" and then checks 1 thru 7 CWS lines and then says "cannot start any client, then says check card.client.conf or network setting. Then about 5 seconds later it starts...still no picture.
emu or plugin, similar. as mentioned which do you want to use? You have all lines hashed out in the xcamclient config file.
Leroy
XCRUISER HDSR600HD twin sat and terrestrial receiver $OOS *
XCRUISER HDSR385 Avant - sold out$OOS UltraPlus DVB-T and DVB-S2 tuners $49 Remotes $OOS
I'm useing Plugin V1.10.05. Id prefer to use Mgcamd. Should I not have all the lines hashed out in the xcamclient config file? Sorry for the dumb questions !
worthp (04-12-13)
Bookmarks