Which MCAS are you using because it should work flawlessly? There is a new version I posted from the 18/1/12 have you tried this?
Leroy
Anyone experimented with redcam on ultra/octa ? mcas is dropping out every few or so minutes, really annoying... thinking redcam might work better, maybe someone can post a working config ?
Look Here -> |
Which MCAS are you using because it should work flawlessly? There is a new version I posted from the 18/1/12 have you tried this?
Leroy
XCRUISER HDSR600HD twin sat and terrestrial receiver $OOS *
XCRUISER HDSR385 Avant - sold out$OOS UltraPlus DVB-T and DVB-S2 tuners $49 Remotes $OOS
Have you tried updating the firmware on your ultraplus? Also update your plugins which will include the latest MCAS. Very easy to install and get working, never had any issues with MCAS and there was new version released this month.
I did a little bit of reading into redcam but found out most of the support was in german and harder to find English forums and English based plugins.
I would try updating your box's firmware (on all boxes) then install the latest MCAS plugin. There is a post in the decoders section, see link below
9200 mcas 18.01.12 & 2.09.87 square pants 5.
pic freezing every few minutes, somesink wrong ...
yes, reset to factory defaults & not sharing
level 96 quality 81
is it possible to permanently remove all the plugins from the receiver ?
in redcam boxkey allows only 15 not 16 char. wtf
You don't need a boxkey with Austar cards plus I don't know that redcam does the 'tweak' that Austar requires hence stick with MCAS.
Delete all your plugins, do a format user data before reloading the MCAS plugin. Then go into the plugin menu, make sure MCAS is set to Auto and Started, highlight MCAS and press OK, select configuration and change reset sequence to T14-T0.
Leroy
XCRUISER HDSR600HD twin sat and terrestrial receiver $OOS *
XCRUISER HDSR385 Avant - sold out$OOS UltraPlus DVB-T and DVB-S2 tuners $49 Remotes $OOS
How can you restore 9200 to default system including plugins? can't delete some plugins...
what if I revert to an older fw ?
installed webinfo and can't fk it off, also after mcas install can't reboot, system just hangs
seenking it needs serial port soft to re-flash the fw, now me suby card shows up as invalid...
and another strange thing i've noticed, when OK on mcas, it sometimes takes up to a minute to get to the menu, same deal when scrolling up/down.
mcas menu lagging only when channel drops out and shows up as scrambled.
Do a restore to factory default. I'll upload MCAS from Nov as this was working ok with all cards.
Delete all plugins, format user data then load plugin. In the MCAS configuration menu change the reset sequence to T14-T0
Leroy
Last edited by LeroyPatrol; 31-01-12 at 08:00 PM.
XCRUISER HDSR600HD twin sat and terrestrial receiver $OOS *
XCRUISER HDSR385 Avant - sold out$OOS UltraPlus DVB-T and DVB-S2 tuners $49 Remotes $OOS
samnewman (31-01-12)
yes,
I have gone back to november mcas. works perfectly with latest firmware and irdeto cards......
No need to change card reset setting for irdeto cards, works fine with default setting.
You did need to change it when using nds cards, but that is not a consideration at the moment, unfortunately.....
Last edited by hoe; 31-01-12 at 10:27 PM.
LeroyPatrol (31-01-12),samnewman (31-01-12)
sweat jebus... hallelujah leroy ! never doubted you for a second ))
but wait there's more... now only 19 transponders? wtf
sorted, network scan must be on...
Bookmarks