C&K 2316i

[Andrewpv01]

Can somebody PM me the instructions for defaulting a 2316i?

I was told by Honeywell that you can't use a default chip in these (yes they told me how to default it but I dodn't right it down )

I will be doing it tomorrow morning if somebody can help me out.

Thanks
Andrew

[Security Man]

Then I would suggest you get a pen and paper before you call them again, if they told you once they should tell you again.

[AusSecTec]

Good day Andrew,
Firstly
Are you an installer or end user, sorry but you must have some basic experience before we can proceed,

Are you sure its a 2316 and not a 236i, 6 or 16 zones,
Why do you require information for defaulting?


Why don't you upgrade to an Eclipse- they are better sorry had to add that one

[Andrewpv01]

I am an installer. I did have about 40 or 50 posts before the crash here.

I now have the info, but the panel was locked out.

I put a Solution 16 in there instead.

Thanks
Andrew

[kalboy]

The eclipse was a rock solid performer............
A pioneer almost. Not the easiest to program from memory.

[Tastech]

Kalboy ill send you anymore we rip out I hated programming them I think we have 2 left in exsistence , Ill admit they are the one panel I hate any other C&K fine to program

[kalboy]

Kalboy ill send you anymore we rip out I hated programming them I think we have 2 left in exsistence , Ill admit they are the one panel I hate any other C&K fine to program

Ah thats right. you pulled the one out i installed at East Dvpt. back when LBS merged with SBT. to become Trust bank.

Good to see a lot of peoples back on the forum ( and using their old names )

[Tastech]

Yep but am missing some of our regulars havent seen them on the forum as yet

[minitechie_94]

surprised middy hasnt tried to get his name back.

oh well, the main thing is we have each other...

[noRbackwards]

surprised middy hasnt tried to get his name back.

oh well, the main thing is we have each other...

Just wait for the spelling mistakes yet I think he is around different name as like me new name no shame

[jobsesber]

Could anyone please advise me how to change the battery of my C & K 236i. If I unplug the alarm system from the power point, will this change all programming? Should I do a *68#. All I want is to change the battery. There is a tamper switch that when the box is open, the alarm goes off. What would be the easiest way of changing battery without changing or erasing codes already in the system. Please send reply also to jobsesber@optusnet.com.au
thanks

[downunderdan]

You shouldn't need to unplug it.

Simply change the battery. The programming is in non-volatile memory, otherwise all a Bad Man would need to do is cut the power and wait for the system to run down a battery.

Go for it. Wear hearing protection if the screamer is mounted near the panel (not usually a great idea) and be ready to enter your code to silence it.

[noRbackwards]

You shouldn't need to unplug it.

Simply change the battery. The programming is in non-volatile memory, otherwise all a Bad Man would need to do is cut the power and wait for the system to run down a battery.

Go for it. Wear hearing protection if the screamer is mounted near the panel (not usually a great idea) and be ready to enter your code to silence it.

Is it not funny when they now supply alarm pamels for the last 30 years without an internal sounder to try and beat someone from ripping the alrm panel of the wall yet over 50% of alarm installations I have sighted have the sounder mounted on or near the contriol panel. Like I say who teaches who and who trained who.

[2Secure]

Is it not funny when they now supply alarm pamels for the last 30 years without an internal sounder to try and beat someone from ripping the alrm panel of the wall yet over 50% of alarm installations I have sighted have the sounder mounted on or near the contriol panel. Like I say who teaches who and who trained who.

Or the keypad is either built into the control panel (eg Lynx, magellan) or mounted on the main control panel.