I'm not familiar with the switch in question, but there is an operating manual available for download at .
I hope that it helps.
Edit:
Have you looked at the Cisco website for information?
They also have support forums at .
Hello, having a boot problem with SRW2024P switch. after connection via console it displays message Firmware 1.0.2 and then get stuck on Diagnostics _
Is there a way to revive that switch or force new firmware update to it?
Thank you
CC
Last edited by CrownClit; 21-10-15 at 02:36 PM.
Look Here -> |
I'm not familiar with the switch in question, but there is an operating manual available for download at .
I hope that it helps.
Edit:
Have you looked at the Cisco website for information?
They also have support forums at .
Last edited by tristen; 21-10-15 at 06:57 PM.
Yes I have unfortunately to get any help out cisco you need to have a valid support contract signed and a device still within the warranty.
I do have a manual for this device and I have done firmware upgrade on those switches before via web interface however for web to work switch needs to boot properly first.
This one like I said earlier is stuck during the boot process and can not pass the diagnostic stage. This means that Web interface is not available and so the menu via console cable and HyperTerminal :-(
Have anyone heard of a lifetime warranty on cisco products?
ASCII stupid question, get a stupid ANSI!
Yes, I realise that you need to have a contract in order to obtain "official" help, but perhaps the forums have some useful advice? You do not need a contract in order to access the community forums - at least not the last time I looked.
I realise that......however for web to work switch needs to boot properly first.
I am aware of that also.....This one like I said earlier is stuck during the boot process and can not pass the diagnostic stage. This means that Web interface is not available and so the menu via console cable and HyperTerminal :-(
I haven't.Have anyone heard of a lifetime warranty on cisco products?
It appears that you will have to continue searching for the information which you require.
Good luck.
Last edited by tristen; 21-10-15 at 10:55 PM.
Trying holding down Ctrl U (or tapping) then power on the unit.
Let me know what comes up
CrownClit (24-10-15)
Hi glich
thank you for your suggestion
I got to this menu now and idea how to use and reconfigure the switch using those options
Image Loader 1.0.2
File Name S/Up Type Size Create Time
--------------------------------- ---- ---- ---------- -----------
$logfile_1 0 3 64 119304615
Factory_Default_Config.cfg 0 5 354 24:00:29
SRW2024P_boot.bix 1 1 1286876 00:00:40
SRW2024P_image.bix 1 2 3667004 25:21:41
certificate 0 8 18040 24:00:23
startup-config 0 5 3261 9758
startup1.cfg 1 5 2764 10894716
startup2.cfg 0 5 2730 10894726
--------------------------------- ---- ---- ---------- ----------
Free Space : 1966080
[X]modem Download [D]elete File [S]et Startup File
[Q]uit
Select>
ASCII stupid question, get a stupid ANSI!
OK, if you're happy that it is reset back to original config - including default password...
Select "Delete File" by hitting D
then type startup-config
Hopefully, that should take it back to factory default and allow you to gain access! Let me know how you go
Boot into romron then upload a default ISO
Hi Gitch
I have deleted the file as per below
Image Loader 1.0.2
File Name S/Up Type Size Create Time
--------------------------------- ---- ---- ---------- -----------
$logfile_1 0 3 64 119304615
Factory_Default_Config.cfg 0 5 354 24:00:29
SRW2024P_boot.bix 1 1 1286876 00:00:40
SRW2024P_image.bix 1 2 3667004 25:21:41
certificate 0 8 18040 24:00:23
startup1.cfg 1 5 2764 10894716
startup2.cfg 0 5 2730 10894726
--------------------------------- ---- ---- ---------- ----------
Free Space : 2097152
[X]modem Download [D]elete File [S]et Startup File
[Q]uit
Select>
but switch still gets stuck on following. Is there a way to disable diagnostics or to check what is causing the problem for diag not to continue
Image Loader 1.0.2
Loading Diagnostic Image File : SRW2024P_boot.bix
Diagnostic 1.0.2
in _
ASCII stupid question, get a stupid ANSI!
You have to use a tftp server
- Check you PM Gitch.
I have tried to use "Transfer/Send File" in Hyper-terminal using Xmodem option but i think some other settings were not correct because file wasn't going anywhere.
Next I will try tftp. Is there anything special i need to with tftp so i don't run in circles?
CC
ASCII stupid question, get a stupid ANSI!
Thanks, bit far to pop over and help out...
When you you tried sending the file, did you select download file on that menu?
how'd you go CC?
Can anybody in this topic help me out with the latest firmware file for the SRW2024P
if yes please PM me.
are there problems with that FW ?
do i need to know anything more?
Bookmarks